Grounding Braid, Straps(2795)

Part	Manufacturer	Description		Stock	Action
815-TS5A23166DCUR	Ultralife	TS5A23166DCUR Overview This electronic part is conveniently packaged in 8-VFSOP (0.091, 2.30mm Width), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. Totally, there are 8 terminations. The electronic part delivers high-quality output through its 2 channels. Powered by a 1.8V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the electrical part body. The analog switch ics are built using SPST - NO switching circuits. TS5A23166 can be used to search for analog multiplexer variants. An switch multiplexer with 900mOhm internal resistance has a value of 900mOhm. Datasheets for 8 pin functions are available upon request. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. The digital multiplexer has a low cost Single supply. The lowest voltage the electronic part should receive is 1.65V. This multiplexer would work with 10nA current. A voltage of 1.65V~5.5V is required for this switch device, which drains from a single voltage source. Put voltage above 100nA on the multiplexer to cause damage. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. There are 150MHz bandwidths for data transfer. It has a Drain to Source resistance of 900mOhm ohms. TS5A23166DCUR Features 2 Channels Switch Circuit: SPST - NO 10nA Supply Current Bandwidth: 150MHz Drain-to-Source resistance: 900mOhm TS5A23166DCUR Applications There are a lot of Texas Instruments TS5A23166DCUR Analog Switches & Multiplexers ICs applications. Central office Data switching Public switching systems Communication systems HDTV DSLAMs Avionics PBX interfaces Medical systems Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads	PDF	999 In-stock	Get Quote
815-SN74LVC2G66DCTR	Ultralife	SN74LVC2G66DCTR Overview The electronic part can be shipped overseas conveniently because it is packaged in 8-LSSOP, 8-MSOP (0.110, 2.80mm Width). The advanced packaging method Cut Tape (CT) provides high reliability. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 8. A electrical component with 2 channels is capable of high-quality output. Turning on and running the electrical part should be easy with a 2.3V voltage supply. It is injected into the electrical part body with 8 pins. Multiplexers built on a SPST - NO switching circuit are built. 74LVC2G66 can be used to search for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 10Ohm. To find out what the 8 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexers or Switches. normally, users should not supply switches with voltages higher than 5.5V. An effective Single supply digital multiplexer. The lowest voltage the electronic part should receive is 1.65V. In order to operate this switch device, it would need a current of 10μA. Using a single voltage supply, this switch device consumes 1.65V~5.5V volts. The analogue multiplexer may be damaged if voltage is greater than 1μA. There are various bandwidths available for data transfer. Drain to Source resistance is 12.5Ohm. SN74LVC2G66DCTR Features 2 Channels Switch Circuit: SPST - NO 10μA Supply Current -3db Bandwidth: 300MHz Bandwidth: 300MHz Drain-to-Source resistance: 12.5Ohm SN74LVC2G66DCTR Applications There are a lot of Texas Instruments SN74LVC2G66DCTR Analog Switches & Multiplexers ICs applications. Data Acquisition Systems Channel Banks Frame Relay Equipment Audio and video signal routing Digital cross connects (DSX-1) DVD-R SDH High reliability control systems Intelligent PBX Switching Systems	PDF	999 In-stock	Get Quote
815-TS3A5018PWR	Ultralife	TS3A5018PWR Overview Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. The total number of terminations is 16. High-quality output is provided by the electronic component's 4 channels. A 2.5V voltage supply should turn on and run the electronic component. A total of 16 pins are injected into the body of the electronic part. The analog switch ics are built using SPDT switching circuits. Try searching for TS3A5018 variants of the analog switch ic. It has an internal resistance of 10Ohm. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. An abnormal situation would be for the switch device to be supplied with a voltage greater than 3.6V. The digital multiplexer has a low cost Single supply. A low voltage of 2.3V should be applied to the electronic component. For this multiplexer to operate, 2.5μA current would be sufficient. A voltage of 1.65V~3.6V is required for this switch device, which drains from a single voltage source. It may damage the digital multiplexer if the voltage is higher than 7μA. Operating voltages range from 3V. 300MHz bandwidths enable data to be transferred. There are 8 outputs on the analogue multiplexer. TS3A5018PWR Features 4 Channels Switch Circuit: SPDT 2.5μA Supply Current Bandwidth: 300MHz TS3A5018PWR Applications There are a lot of Texas Instruments TS3A5018PWR Analog Switches & Multiplexers ICs applications. Channel Banks Industrial control systems New designs requiring multiplexer functions Routers ADCs such as AD7840/8, AD7870/1/2/4/5/6/8 Precision test equipment RGB switches SONET Cable Modem Remote wireless modules	PDF	999 In-stock	Get Quote
815-TS3A44159PWR	Ultralife	TS3A44159PWR Overview Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. There is 2:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. 16 terminations have been made so far. A electrical component with 4 channels is capable of high-quality output. If the voltage supply is 1.8V volts, the electrical component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Circuits based on SPDT switching are used to construct these analog switch ics. There are 4 circuits in this switch device. TS3A44159 can be used to search for analog multiplexer variants. Analog switches have 450mOhm internal resistance. You can find the functions of the 16 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 4.3V to a switch device. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 1.65V. This multiplexer would work with 15nA current. This analog switch requires a voltage of 1.65V~4.3V to drain from a single voltage supply. Put voltage above 400nA on the multiplexer to cause damage. There are SEPARATE OUTPUT outputs on this analog switch ic. It can operate from 3V operating voltages. Operating 2 inputs is required. A 35MHz-bandwidth can be used for data transfer. It has a Drain to Source resistance of 300mOhm ohms. TS3A44159PWR Features 4 Channels Switch Circuit: SPDT 15nA Supply Current Bandwidth: 35MHz Drain-to-Source resistance: 300mOhm TS3A44159PWR Applications There are a lot of Texas Instruments TS3A44159PWR Analog Switches & Multiplexers ICs applications. Cable PC Transmit New designs requiring multiplexer functions Optical Applications Existing multiplexer applications (both fault-protected and nonfault-protected) Digital cross connects (DSX-1) HDTV Industrial control systems Cell phones DVD-R	PDF	999 In-stock	Get Quote
feilidi-TS5A9411DCKR	Ultralife	<h3>TS5A9411DCKR Overview</h3><div><br/>The electronic part can be shipped overseas conveniently because it is packaged in 6-TSSOP, SC-88, SOT-363. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. In total, there are 6 terminations. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 2.5V volts, the electrical component should be turned on and run. 6 pins are injected to the electronic part body. The analog switch ics are built using SPDT switching circuits. Look for analog switch ic variants by searching with TS5A9411. An switch multiplexer with 10Ohm internal resistance has a value of 10Ohm. To find out what the functions of 6 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 2.25V. For this digital switch to work, 10nA current would suffice. Analogue multiplexers require a 2.25V~5.5V voltage to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 500nA. Among the inputs that can be operated are the 1 inputs. The data can be transferred over a wide range of bandwidths, called 100MHz bandwidths. This electronic component presents a Drain to Source resistance of 10Ohm. The analogue multiplexer has 2 outputs. <br/><br/></div><h3>TS5A9411DCKR Features</h3><div><br/>1 Channels<br/>Switch Circuit: SPDT<br/>10nA Supply Current<br/>Bandwidth: 100MHz<br/>Drain-to-Source resistance: 10Ohm<br/><br/></div><h3>TS5A9411DCKR Applications</h3><div><br/>There are a lot of Texas Instruments TS5A9411DCKR Analog Switches & Multiplexers ICs applications. <br/><br/></div><ul style="padding: 0px; margin: 0px;"><li>Avionics and Military Systems<!--<li--></li><li>Residential Gateways, Home Gateway/Router<!--<li--></li><li>Audio/video switches <!--<li--></li><li>Sample hold systems<!--<li--></li><li>Avionics test equipment<!--<li--></li><li>MP3 players<!--<li--></li><li>FTTH<!--<li--></li><li>Intelligent PBX<!--<li--></li><li>Channelized and Unchannelized DS3 applications<!--<li--></li><li>T1/E1 Terminals<!--<li--></li></ul>	PDF	999 In-stock	Get Quote
761-STG3693QTR	Klein Tools, Inc.	STG3693QTR Overview Packed in 16-UFQFN Exposed Pad, the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -55°C~125°C TA. In total, there have been 16 terminations. By its 1 channels, the electronic component provides high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Multiplexers built on a SPDT switching circuit are built. Using the STG3693 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 5.2Ohm. Datasheets for 16 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. Multiplexers should not be powered above 4.3V in normal situations. Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 1.65V. 100nA current would be enough for this multiplexer to operate. This analog switch requires a voltage of 1.65V~4.3V to drain from a single voltage supply. Put voltage above 100nA on the multiplexer to cause damage. In order to operate the 4 inputs, there are several steps to follow. A 800MHz-bandwidth can be used for data transfer. A analog switch ics with 8 outputs is included. STG3693QTR Features 1 Channels Switch Circuit: SPDT 100nA Supply Current Bandwidth: 800MHz STG3693QTR Applications There are a lot of STMicroelectronics STG3693QTR Analog Switches & Multiplexers ICs applications. Industrial Industrial control systems Precision data acquisition Mechanical reed relay replacement PDH Multiplexers Routers SDH/SONET multiplexers Industrial and process control systems Microwave transmission systems Microprocessor Controlled Analog Systems	PDF	999 In-stock	Get Quote
815-TS3A44159RGTR	Ultralife	TS3A44159RGTR Overview Presented in 16-VFQFN Exposed Pad, this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. There are 16 terminations totally. A electrical component with 4 channels is capable of high-quality output. Powered by a 1.8V voltage supply, the electrical part should be switched on and run. A total of 16 pins are injected into the body of the electronic part. A SPDT switching circuit is used to build these analog multiplexers. Try searching with TS3A44159 to find analog multiplexer variants. This digital multiplexer has 450mOhm internal resistance. Datasheets for 16 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 4.3V. Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 1.65V. The analogue multiplexer could operate on 15nA current. Analogue multiplexers require a 1.65V~4.3V voltage to drain from a single voltage supply. Putting voltage greater than 400nA on the multiplexer may cause damage. There is a voltage range of 3V operating voltages for the electrical part. Operating the 4 inputs requires 4 inputs. A 35MHz-bandwidth can be used for data transfer. There is 450mOhm resistance between the Drain and Source on this part. A analog switch ics with 8 outputs is included. TS3A44159RGTR Features 4 Channels Switch Circuit: SPDT 15nA Supply Current Bandwidth: 35MHz Drain-to-Source resistance: 450mOhm TS3A44159RGTR Applications There are a lot of Texas Instruments TS3A44159RGTR Analog Switches & Multiplexers ICs applications. FTTH MP3 players PDH Multiplexers ADCs such as AD7840/8, AD7870/1/2/4/5/6/8 SDH/SONET multiplexers Remote Powered Equipment Automotive applications Medical Instrumentation Existing multiplexer applications (both fault-protected and nonfault-protected) Industrial and process control systems	PDF	250 In-stock	Get Quote
815-TS3A24159YZPR	Ultralife	TS3A24159YZPR Overview Due to its 10-XFBGA, DSBGA packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. The operating temperature is extended to around -40°C~85°C TA. Totally, there are 10 terminations. By its 2 channels, the electronic component provides high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 10 pins. Circuits based on SPDT switching are used to construct these analog switch ics. TS3A24159 can be used to search for analog multiplexer variants. There is 300mOhm internal resistance in this digital multiplexer. For details about the functions of 10 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 3.6V volts for the multiplexer. Digital switch that provides Single power at a cost-effective price. 1.65V should be the lowest voltage fed to the electronic component. In order to operate this switch device, it would need a current of 15nA. This analog switch requires a voltage of 1.65V~3.6V to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 100nA. In order to operate the 2 inputs, there are several steps to follow. It is possible to transfer data over a 23MHz-bandwidth. In this digital multiplexer, there are 4 outputs. TS3A24159YZPR Features 2 Channels Switch Circuit: SPDT 15nA Supply Current Bandwidth: 23MHz TS3A24159YZPR Applications There are a lot of Texas Instruments TS3A24159YZPR Analog Switches & Multiplexers ICs applications. High speed data transmission line cards Cellular phones Private Branch Exchange (PBX) High reliability control systems ATM ADCs such as AD7840/8, AD7870/1/2/4/5/6/8 Relay replacements MP3 players Avionics test equipment Sample-and-hold systems	PDF	999 In-stock	Get Quote
815-TS5A21366DCUR	Ultralife	TS5A21366DCUR Overview This electronic part is conveniently packaged in 8-VFSOP (0.091, 2.30mm Width), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature extended to -40°C~85°C TA. In total, there are 8 terminations. A electrical component with 2 channels is capable of high-quality output. Turning on and running the electrical part should be easy with a 1.8V voltage supply. A total of 8 pins are injected into the electrical part body. Multiplexers built on a SPST - NO switching circuit are built. Using the TS5A21366 search parameter, you can discover variants of the switch. This digital multiplexer has 1Ohm internal resistance. Datasheets for 8 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. Digital switch that provides Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 1.65V. It would be sufficient to run this analogue multiplexer with 9μA current. A voltage of 1.65V~5.5V is required for this switch device, which drains from a single voltage source. Put voltage above 9μA on the multiplexer to cause damage. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating the 2 inputs requires 2 inputs. In 260MHz-bandwidths, data can be transferred. You shouldn't miss the additional features of the electrical component, such as: VIDEO APPLICATION. There is 750mOhm Drain to Source resistance on this electronic part. TS5A21366DCUR Features 2 Channels Switch Circuit: SPST - NO 9μA Supply Current Bandwidth: 260MHz Additional Features: VIDEO APPLICATION Drain-to-Source resistance: 750mOhm TS5A21366DCUR Applications There are a lot of Texas Instruments TS5A21366DCUR Analog Switches & Multiplexers ICs applications. T1/E1 Terminals Optical Applications Remote Powered Equipment Precision data acquisition Communications systems PDH Multiplexers MP3 players ATM Digital access cross connects Medical systems	PDF	999 In-stock	Get Quote
815-TS5A3159AYZPR	Ultralife	TS5A3159AYZPR Overview Packed in 6-XFBGA, DSBGA, the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. The total number of terminations is 6. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 1.8V, it should be turned on and run. It is injected into the electrical part body with 6 pins. Unlike digital switches, these are based on SPDT switching circuits. Using the TS5A3159 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 1.1Ohm. For details about the functions of 6 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 1.65V. This digital switch can be operated with a current of 100nA. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. The analogue multiplexer may be damaged if voltage is greater than 50nA. It is possible to transfer data over a 100MHz-bandwidth. The analog switch ics includes 2 outputs. TS5A3159AYZPR Features 1 Channels Switch Circuit: SPDT 100nA Supply Current Bandwidth: 100MHz TS5A3159AYZPR Applications There are a lot of Texas Instruments TS5A3159AYZPR Analog Switches & Multiplexers ICs applications. HDTV PBX interfaces SONET Cable Telephony – NIU, Set-Top Box, Home Side Box Microwave transmission systems Video switching Medical systems PDH Multiplexers Intelligent PBX Relay replacements	PDF	999 In-stock	Get Quote
815-CD74HC4052M96	Ultralife	CD74HC4052M96 Overview The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Cut Tape (CT). In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 4:1. Operating temperature around -55°C~125°C TA extended. There are 16 terminations totally. This electronic part offers high-quality output due to its 8 channels. An 4.5V voltage supply should allow the electrical part to be turned on and run. An injection of 16 pins is performed into the body of the electrical component. These analog multiplexers are built based on SP4T switching circuits. This multiplexer is composed of 2 circuits. If you are looking for variants of the digital switch, trying search with 74HC4052. Analog switches have 130Ohm internal resistance. Datasheets for 16 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 6V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended to use 2V as the lowest voltage for the electrical part. The switch device would be able to operate with 160μA current. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 5V. For dual power supplies, a voltage of at least 1V should be attached. It is integrated with DIFFERENTIAL MULTIPLEXER analog ICs. 185MHz bandwidths enable data to be transferred. There is 130mOhm resistance between Drain and Source for this electronic part. The switch device is capable of conducting in a 4-bit mode. CD74HC4052M96 Features 8 Channels Switch Circuit: SP4T 160μA Supply Current Bandwidth: 185MHz Drain-to-Source resistance: 130mOhm 4-Bit CD74HC4052M96 Applications There are a lot of Texas Instruments CD74HC4052M96 Analog Switches & Multiplexers ICs applications. Avionics test equipment Cell phones Audio and video routing Video signal routing Avionics and Military Systems E1 Network Equipment Routers Frame Relay Equipment E1 Multiplexer Cross Connects	PDF	999 In-stock	Get Quote
815-TS3A27518ERTWR	Ultralife	TS3A27518ERTWR Description A high-performance 8:1 analog multiplexer/demultiplexer switch made for single-supply systems is the TS3A27518ERTWR. It has a wide operating temperature range of -40°C to 125°C, low on-state resistance (Ron), and low charge injection. The component is appropriate for applications with limited space, such as handheld devices, industrial control systems, and communication systems since it is located in a compact 20-pin QFN package. TS3A27518ERTWR Features Small 20-pin QFN package Rail-to-rail inputs and outputs ESD protection (2 kV HBM, 400 V CDM) Wide supply voltage range (1.8 V to 5.5 V) Extended temperature range (-40°C to 125°C) Compatible with CMOS and LV-CMOS logic levels Low Ron (0.05 Ω) and low charge injection (< 1 pC) 8:1 high-performance analog multiplexer/demultiplexer switch Break-before-make switching action for hot-swapping capability High off-isolation (> 60 dB at 1 MHz) and low crosstalk (< -55 dB at 1 MHz) TS3A27518ERTWR Applications Medical equipment Data acquisition systems Communication systems Test and measurement systems Aerospace and defense systems Audio and video signal switching Battery-powered portable devices Industrial automation equipment	PDF	999 In-stock	Get Quote
815-TS5A23159DGST	Ultralife	TS5A23159DGST Overview The electrical component comes in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. The operating temperature is extended to around -40°C~85°C TA. There are 10 terminations totally. A high-quality output is provided by the electrical component's 2 channels. A 1.8V voltage supply should turn on and run the electronic component. 10 pins are injected to the electronic part body. Multiplexers built on a SPDT switching circuit are built. Try searching for the analog switch ic with TS5A23159 if you are looking for variants. This digital multiplexer has 900mOhm internal resistance. To find out what the functions of 10 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. An effective Single supply digital multiplexer. 1.65V is the lowest voltage the electrical component should receive. For this digital switch to work, 10nA current would suffice. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 50μA. Operating 2 inputs is required. It is possible to transfer data over a 100MHz-bandwidth. Don’t miss additional features of the electronic component such as: VIDEO APPLICATION. A Drain to Source resistance of 1.1Ohm is shown for this electronic part. The analog switch ics includes 4 outputs. TS5A23159DGST Features 2 Channels Switch Circuit: SPDT 10nA Supply Current Bandwidth: 100MHz Additional Features: VIDEO APPLICATION Drain-to-Source resistance: 1.1Ohm TS5A23159DGST Applications There are a lot of Texas Instruments TS5A23159DGST Analog Switches & Multiplexers ICs applications. SONET/SDH ADM Industrial Isolation Avionics and Military Systems DSLAMs Avionics test equipment Imaging Central office Routers Precision data acquisition	PDF	999 In-stock	Get Quote
815-MUX508IPWR	Ultralife	MUX508IPWR Overview This electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. The advanced packaging method Tape & Reel (TR) provides high reliability. It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 8:1. Operating temperature extended to -40°C~125°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. This multiplexer is composed of 1 circuits. Try searching for the analog switch ic with MUX508 if you are looking for variants. It has an internal resistance of 170Ohm. The datasheets for the 16 pins explain the functions. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. The outputs of this digital multiplexer are COMMON OUTPUT in number. There are various bandwidths available for data transfer. There is 200Ohm Drain to Source resistance on this electronic part. MUX508IPWR Features 1 Channels Bandwidth: 500MHz Drain-to-Source resistance: 200Ohm MUX508IPWR Applications There are a lot of Texas Instruments MUX508IPWR Analog Switches & Multiplexers ICs applications. Channel Banks Frame Relay Equipment Central office USB 1.1 signal switching circuits Channelized and Unchannelized DS3 applications SDH/SONET multiplexers Cable Telephony – NIU, Set-Top Box, Home Side Box Cross Connects Signal routing between systems Digital access cross connects	PDF	999 In-stock	Get Quote
815-SN74LVC1G66YZPR	Ultralife	SN74LVC1G66YZPR Overview The electronic component is convenient to ship overseas because it is packed in a 5-XFBGA, DSBGA. To ensure high reliability, a new packaging method Cut Tape (CT) is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Operating temperature extended to -40°C~85°C TA. In total, 5 terminations have occurred. The electronic part provides high-quality output because it has 1 channels. An 1.8V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 5 series. Unlike digital switches, these are based on SPST - NO switching circuits. Search with 74LVC1G66 if you are looking for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 10Ohm. To find out what the functions of 5 pins are, please refer to their datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 1.65V. It would be sufficient to run this analogue multiplexer with 10μA current. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. Put voltage above 10μA on the multiplexer to cause damage. This product is integrated with an analog integrated circuit (IC) of type SPDT. The transfer of data can be performed over 300MHz bandwidths. SN74LVC1G66YZPR Features 1 Channels Switch Circuit: SPST - NO 10μA Supply Current -3db Bandwidth: 300MHz Bandwidth: 300MHz SN74LVC1G66YZPR Applications There are a lot of Texas Instruments SN74LVC1G66YZPR Analog Switches & Multiplexers ICs applications. Channelized and Unchannelized DS3 applications Routers Medical Instrumentation Intelligent PBX Residential Gateways, Home Gateway/Router Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads Battery Powered Systems Cable PC Switching Systems PDAs	PDF	999 In-stock	Get Quote
815-SN74LV4066APWR	Ultralife	SN74LV4066APWR Overview This electronic part is conveniently packaged in 14-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. The advanced packaging method Tape & Reel (TR) provides high reliability. This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 14 terminations. A 4 channel electronic part produces high-quality output. When a voltage supply of 2.3V is used, the electronic component should be turned on and run. An electrical component like this is included in the 14 series. These analog multiplexers are built based on SPST - NO switching circuits. Look for analog switch ic variants by searching with 74LV4066. Internally, this switch multiplexer has a resistance of 75Ohm. Please refer to the datasheets for 14 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. An effective Single supply digital multiplexer. 2V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 20μA current. An analogue multiplexer drains from a single voltage supply at 2V~5.5V. It may damage the digital multiplexer if the voltage is higher than 20μA. In 50MHz-bandwidths, data can be transferred. There is 38Ohm resistance between Drain and Source for this electronic part. SN74LV4066APWR Features 4 Channels Switch Circuit: SPST - NO 20μA Supply Current Bandwidth: 50MHz Drain-to-Source resistance: 38Ohm SN74LV4066APWR Applications There are a lot of Texas Instruments SN74LV4066APWR Analog Switches & Multiplexers ICs applications. Signal routing between systems DSLAMs CSU Cross Connects Industrial and process control systems Cell phones FTTH Isolation Audio signal routing Switching Systems	PDF	999 In-stock	Get Quote
815-TS5A3157YZPR	Ultralife	TS5A3157YZPR Overview Packed in 6-XFBGA, DSBGA, the electronic component is convenient for shipping overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Extended operating temperature around -40°C~85°C TA. Totally, there are 6 terminations. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 1.8V voltage supply. A key feature of the 6 series is the inclusion of this electronic part as part of its design. A SPDT switching circuit is used to build these analog multiplexers. Try searching with TS5A3157 if you're looking for variants. This digital multiplexer has 10Ohm internal resistance. Please refer to the datasheets for 6 pins functions. Multiplexer or Switches is a typical switch device. A voltage higher than 5.5V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. In order for the electronic part to function properly, the lowest voltage should be 1.65V. For this digital switch to work, 2.5μA current would suffice. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 5μA. It is possible to transfer data over a 300MHz-bandwidth. Additional features of the electronic component include: VIDEO APPLICATION. An output of 2 is provided by the digital multiplexer. TS5A3157YZPR Features 1 Channels Switch Circuit: SPDT 2.5μA Supply Current Bandwidth: 300MHz Additional Features: VIDEO APPLICATION TS5A3157YZPR Applications There are a lot of Texas Instruments TS5A3157YZPR Analog Switches & Multiplexers ICs applications. Imaging Audio and video signal routing Data Acquisition Systems DSUs New designs requiring multiplexer functions Mechanical reed relay replacement Central office High reliability control systems Fiber to the Home Public switching systems	PDF	999 In-stock	Get Quote
815-CD4053BNSR	Ultralife	CD4053BNSR Overview Due to its 16-SOIC (0.209, 5.30mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 2:1. Extended operating temperature around -55°C~125°C TA. In total, there have been 16 terminations. A high-quality output is provided by the electrical component's 2 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. There are 16 pins injected into the electronic part body. Multiplexers built on a SPDT switching circuit are built. It consists of 3 circuits. Try searching with CD4053 if you're looking for variants. This digital multiplexer has 240Ohm internal resistance. Please refer to the datasheets for 16 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 20V to a switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 3V. The switch device would be able to operate with 80nA current. Despite this switch's dual supply capability, its voltage should not exceed 9V. If you are using dual power supplies, you should attach at least 2.5V. It is integrated with a SINGLE-ENDED MULTIPLEXER analog IC. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. It can operate from 18V operating voltages. In order to operate the 6 inputs, there are several steps to follow. 30MHz bandwidths enable data to be transferred. CD4053BNSR Features 2 Channels Switch Circuit: SPDT 80nA Supply Current Bandwidth: 30MHz CD4053BNSR Applications There are a lot of Texas Instruments CD4053BNSR Analog Switches & Multiplexers ICs applications. Isolation Medical Instrumentation Existing multiplexer applications (both fault-protected and nonfault-protected) PBXs Industrial Digital cross connects (DSX-1) Frame Relay Equipment T1/E1 Terminals Precision test equipment Multiplexers	PDF	999 In-stock	Get Quote
815-TS5A3166DCKRG4	Ultralife	TS5A3166DCKRG4 Overview This electronic part is conveniently packaged in 5-TSSOP, SC-70-5, SOT-353, making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. Around -40°C~85°C TA is the extended operating temperature. The total number of terminations is 5. This electronic part offers high-quality output due to its 1 channels. An 1.8V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 5 series. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching for the analog switch ic with TS5A3166 if you are looking for variants. In this multiplexer, the internal resistance is 900mOhm. The datasheets for the 5 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. 1.65V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 10nA would be sufficient for this switch device. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. When the digital multiplexer is charged above 100nA, damage can occur. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Among the inputs that can be operated are the 1 inputs. It is possible to transfer data over a 200MHz-bandwidth. TS5A3166DCKRG4 Features 1 Channels Switch Circuit: SPST - NO 10nA Supply Current Bandwidth: 200MHz TS5A3166DCKRG4 Applications There are a lot of Texas Instruments TS5A3166DCKRG4 Analog Switches & Multiplexers ICs applications. Residential Gateways, Home Gateway/Router Microprocessor controlled systems SONET/SDH ADM Communication systems ADCs such as AD7840/8, AD7870/1/2/4/5/6/8 Access Concentrators Imaging Remote Powered Equipment Fiber to the Home PBX interfaces	PDF	999 In-stock	Get Quote
815-SN74HC4066NSR	Ultralife	SN74HC4066NSR Overview Due to its 14-SOIC (0.209, 5.30mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -40°C~85°C TA. In total, 14 terminations have occurred. A high-quality output is provided by the electrical component's 4 channels. A 4.5V voltage supply should turn on and run the electronic component. There are 14 pins injected into the electronic part body. Based on SPST - NO switching circuits, these analog multiplexers work. Use 74HC4066 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 30Ohm. To find out what the 14 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 6V. Single supply type digital switch with a low cost. A low voltage of 2V should be applied to the electronic component. The analogue multiplexer could operate on 2μA current. This analog switch requires a voltage of 2V~6V to drain from a single voltage supply. When the digital multiplexer is charged above 2μA, damage can occur. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. It is possible to transfer data over a 30MHz-bandwidth. SN74HC4066NSR Features 4 Channels Switch Circuit: SPST - NO 2μA Supply Current Bandwidth: 30MHz SN74HC4066NSR Applications There are a lot of Texas Instruments SN74HC4066NSR Analog Switches & Multiplexers ICs applications. Ultrasound DVD-R Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads Microwave transmission systems ISDN NT1/TA Channelized and Unchannelized DS3 applications Audio and video switching Battery-powered systems PDH Multiplexers Precision instrumentation	PDF	999 In-stock	Get Quote
815-SN74AUC2G53DCTR	Ultralife	SN74AUC2G53DCTR Overview Shipping overseas is convenient due to the electrical component's packing in 8-LSSOP, 8-MSOP (0.110, 2.80mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -40°C~85°C TA. Total terminations are 8. This electronic part offers high-quality output due to its 2 channels. With a 1.1V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 8 pins. A SPDT switching circuit is used to build these analog multiplexers. It consists of 1 circuits. Try searching for the analog switch ic with 74AUC2G53 if you are looking for variants. This digital multiplexer has 15Ohm internal resistance. The datasheets for the 8 pins explain the functions. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 2.7V should not normally be supplied to the switches. Analog switch ics with Single supply type are cost-effective. A low voltage of 800mV should be applied to the electronic component. The switch device would be able to operate with 10μA current. A voltage of 0.8V~2.7V is required for this switch device, which drains from a single voltage source. If you put voltage higher than 10μA on the digital multiplexer, damage may occur. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. There are 2 inputs to be operated. It is possible to transfer data over a 500MHz-bandwidth. SN74AUC2G53DCTR Features 2 Channels Switch Circuit: SPDT 10μA Supply Current -3db Bandwidth: 50MHz Bandwidth: 500MHz SN74AUC2G53DCTR Applications There are a lot of Texas Instruments SN74AUC2G53DCTR Analog Switches & Multiplexers ICs applications. Fiber In The Loop (FITL) SONET Medical Instrumentation Industrial control systems HDTV Communication systems Cable PC Battery-powered systems PDAs Relay replacements	PDF	999 In-stock	Get Quote
761-STG4160BJR	Klein Tools, Inc.	STG4160BJR Overview Due to its 8-UFBGA, FCBGA packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 2:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 8 terminations. This electrical component is included in the 8 series of products. On the other hand, analog switches can be constructed using SPDT switching circuits. STG4160 can be used to search for analog multiplexer variants. Analog switches have 500mOhm internal resistance. You can find the functions of the 8 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 4.8V voltage to the switch device. Digital switch that provides Single power at a cost-effective price. 1.65V is the lowest voltage that should be fed to the electronic electronic part. Using a single voltage supply, this switch device consumes 1.65V~4.8V volts. The analogue multiplexer may be damaged if voltage is greater than 50nA. It is possible to operate 1 inputs. The analogue multiplexer has 2 outputs. STG4160BJR Features Switch Circuit: SPDT -3db Bandwidth: 50MHz STG4160BJR Applications There are a lot of STMicroelectronics STG4160BJR Analog Switches & Multiplexers ICs applications. MP3 players Digital Cross-Connects Access Concentrators Routers DVD-R Isolation Power routing Automotive applications Voice over IP/DSL – Integrated Access Devices, Smart Industrial and process control systems	PDF	999 In-stock	Get Quote
815-TS5A2053DCUR	Ultralife	TS5A2053DCUR Overview Packed in 8-VFSOP (0.091, 2.30mm Width), the electronic component is convenient for shipping overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. A switch device like this is mounted in Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. There are 8 terminations totally. This electronic part offers high-quality output due to its 1 channels. When a voltage supply of 1.8V is used, the electronic component should be turned on and run. There is an electrical component included in the 8 series. Based on SPDT switching circuits, these analog multiplexers work. A 1 circuit is present in this switch device. Try searching with TS5A2053 if you're looking for variants. There is 13.8Ohm internal resistance in this digital multiplexer. You can find the functions of the 8 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Single supply type digital switch with a low cost. There should be 1.65V voltage fed to the electrical part below 1.65V. The switch device would be able to operate with 100nA current. The voltage required by this switch device is 1.65V~5.5V, draining from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. 330MHz bandwidths enable data to be transferred. 2 outputs are included in the analogue multiplexer. TS5A2053DCUR Features 1 Channels Switch Circuit: SPDT 100nA Supply Current Bandwidth: 330MHz TS5A2053DCUR Applications There are a lot of Texas Instruments TS5A2053DCUR Analog Switches & Multiplexers ICs applications. Data switching Mechanical reed relay replacement Routers FTTH Audio and video signal routing Fault Tolerant Systems Imaging SDH/SONET multiplexers Medical Industrial and process control systems	PDF	999 In-stock	Get Quote
761-74H1G66STR	Klein Tools, Inc.	74H1G66STR Overview Presented in SC-74A, SOT-753, this electrical component is convenient for overseas shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, this analog switch is mounted. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -55°C~125°C TA. A total of 5 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. A 4.5V voltage supply should turn on and run the electronic component. This electrical component is included in the 5 series of products. SPST - NO switching circuits are used in these analog switch ics. 74H1G66 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 80Ohm. The datasheets for the 5 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. A cost-effective Single supply type analogue multiplexer. 2V should be the lowest voltage fed to the electronic component. Analogue multiplexers require a 2V~12V voltage to drain from a single voltage supply. If put voltage greater than 8μA on the device, damage may be caused to the analogue multiplexer. 74H1G66STR Features 1 Channels Switch Circuit: SPST - NO -3db Bandwidth: 180MHz 74H1G66STR Applications There are a lot of STMicroelectronics 74H1G66STR Analog Switches & Multiplexers ICs applications. PDH Multiplexers Sample-and-hold systems Switching Systems T1/E1 Terminals 65 V DACs High-Voltage Battery Powered Instruments Audio signal routing DSLAMs Avionics and Military Systems	PDF	999 In-stock	Get Quote
815-CD4052BM96G3	Ultralife	CD4052BM96G3 Overview Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 4:1. Operating temperature around -55°C~125°C TA extended. Total terminations are 16. This electronic part offers high-quality output due to its 4 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. The electronic part body is injected with 16 pins. SP4T switching circuits are used in these analog switch ics. Circuits number 2 make up this analogue multiplexer. Using the CD4052 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 240Ohm. For functions related to 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 20V volts for the multiplexer. An effective Dual, Single supply digital multiplexer. 3V should be the lowest voltage fed to the electronic component. An operating current of 80nA would be sufficient for this switch device. For this multiplexer, dual supply voltage is feasible, but it should not exceed 9V. If you are using a dual power supply, you should attach at least 2.5V. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. 18V operating voltages are supported by the electronic component. Among the inputs that can be operated are the 8 inputs. The transfer of data can be performed over 25MHz bandwidths. Drain to Source resistance is 240Ohm. 4-bits are supported. CD4052BM96G3 Features 4 Channels Switch Circuit: SP4T 80nA Supply Current Bandwidth: 25MHz Drain-to-Source resistance: 240Ohm 4-Bit CD4052BM96G3 Applications There are a lot of Texas Instruments CD4052BM96G3 Analog Switches & Multiplexers ICs applications. ISDN NT1/TA USB 1.1 signal switching circuits PDH Multiplexers Public switching systems CSU E1 Multiplexer Industrial control systems High reliability control systems Signal routing between systems Voice over IP/DSL – Integrated Access Devices, Smart	PDF	999 In-stock	Get Quote
815-CD4051BPWRG4	Ultralife	CD4051BPWRG4 Overview The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 8:1. Operating temperature extended to -55°C~125°C TA. In total, there are 16 terminations. The electronic part delivers high-quality output through its 8 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. The electrical component body receives 16 pins. There are 1 circuits in this multiplexer. Using the CD4051 search parameter, you can discover variants of the switch. Internally, this switch multiplexer has a resistance of 240Ohm. To find out what the 16 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 20V volts for the multiplexer. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 3V is the lowest voltage that should be fed to the electronic electronic part. It would be sufficient to run this analogue multiplexer with 80nA current. For this multiplexer, dual supply voltage is feasible, but it should not exceed 9V. For dual power supplies, a voltage of at least 2.5V should be attached. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. A voltage of 18V can be used to operate the electronic component. In order to operate the 8 inputs, there are several steps to follow. A 20MHz-bandwidth can be used for data transfer. CD4051BPWRG4 Features 8 Channels 80nA Supply Current Bandwidth: 20MHz CD4051BPWRG4 Applications There are a lot of Texas Instruments CD4051BPWRG4 Analog Switches & Multiplexers ICs applications. Audio and video switching ATM PBX interfaces Communications systems Automatic test equipment Microprocessor Controlled Analog Systems Audio and video signal routing Cellular phones Data switching High-Voltage	PDF	999 In-stock	Get Quote
815-TS5A23157DGSRG4	Ultralife	TS5A23157DGSRG4 Overview Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 2:1. Temperatures around -40°C~85°C TA are extended for operation. 10 terminations have been made so far. This electronic part offers high-quality output due to its 2 channels. When the electronic component is given a voltage of 1.8V, it should be turned on and run. As part of the design of the 10 series, this electronic part has been incorporated into the system. SPDT switching circuits are used in these analog switch ics. There are 2 circuits in this switch device. Try searching with TS5A23157 if you're looking for variants. As far as internal resistance is concerned, it has 10Ohm. Datasheets for functions of 10 pins are available. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. The analog switch ic is of the Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 1.8V. In order to operate this switch device, it would need a current of 1μA. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Operating 2 inputs is required. In 220MHz-bandwidths, data can be transferred. Don’t miss additional features of the electronic component such as: VIDEO APPLICATION. The analog switch ics includes 4 outputs. TS5A23157DGSRG4 Features 2 Channels Switch Circuit: SPDT 1μA Supply Current Bandwidth: 220MHz Additional Features: VIDEO APPLICATION TS5A23157DGSRG4 Applications There are a lot of Texas Instruments TS5A23157DGSRG4 Analog Switches & Multiplexers ICs applications. T1/E1 Terminals Digital access cross connects Ultrasound E1 Network Equipment Audio and video signal routing Cell phones Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads Digital Cross-Connects PCMCIA cards RGB switches	PDF	999 In-stock	Get Quote
815-SN74LV4053APWRG4	Ultralife	SN74LV4053APWRG4 Overview The electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. Totally, there are 16 terminations. By its 2 channels, the electronic component provides high-quality output. A 2.3V voltage supply should turn on and run the electronic component. 16 pins are injected to the electronic part body. A SPDT switching circuit is used for these analog switches. There are 3 circuits in this multiplexer. If you are looking for variants of the digital switch, trying search with 74LV4053. This digital multiplexer has 75Ohm internal resistance. Datasheets for 16 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Digital switch that provides Single power at a cost-effective price. There should be 2V voltage fed to the electrical part below 2V. The switch device would be able to operate with 20μA current. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. There are SEPARATE OUTPUT outputs on this analog switch ic. It is possible to operate 6 inputs. 50MHz-bandwidths can be used to transfer data between multiplexers. SN74LV4053APWRG4 Features 2 Channels Switch Circuit: SPDT 20μA Supply Current Bandwidth: 50MHz SN74LV4053APWRG4 Applications There are a lot of Texas Instruments SN74LV4053APWRG4 Analog Switches & Multiplexers ICs applications. Audio and video signal routing 65 V DACs Ultrasound HDTV Video signal routing High reliability control systems Battery Powered Instruments Communication systems FTTH Fault Tolerant Systems	PDF	999 In-stock	Get Quote
761-M74HCT4053RM13TR	Klein Tools, Inc.	M74HCT4053RM13TR Overview Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. The operating temperature is extended to around -55°C~125°C TA. There are 16 terminations totally. By its 2 channels, the electronic component provides high-quality output. With a 4.5V voltage supply, the electrical component should be turned on and run. The electronic part body is injected with 16 pins. A SPDT switching circuit is used to build these analog multiplexers. Circuits number 3 make up this analogue multiplexer. If you are looking for variants of the digital switch, trying search with M74HCT405. It has an internal resistance of 120Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. Analogue multiplexer with a Dual supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 4.5V. It would be sufficient to run this analogue multiplexer with 8μA current. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. If you are using a dual power supply, you should attach at least 1V. It is integrated with SINGLE-ENDED MULTIPLEXER analog ICs. A voltage of 5V can be used to operate the electronic component. The electrical component supports 6 inputs. It is possible to transfer data over a 120MHz-bandwidth. M74HCT4053RM13TR Features 2 Channels Switch Circuit: SPDT 8μA Supply Current -3db Bandwidth: 190MHz Bandwidth: 120MHz M74HCT4053RM13TR Applications There are a lot of STMicroelectronics M74HCT4053RM13TR Analog Switches & Multiplexers ICs applications. Medical systems Remote Powered Equipment Ultrasound Multiplexers Audio and video signal routing ATM Precision instrumentation Battery Powered Systems Sample hold systems SONET	PDF	999 In-stock	Get Quote
815-SN74LV4053ATDRQ1	Ultralife	SN74LV4053ATDRQ1 Overview As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~105°C TA. Total terminations are 16. This electronic part offers high-quality output due to its 3 channels. When a voltage supply of 2.3V is used, the electronic component should be turned on and run. This electronic part can be found in the 16 series. SPDT switching circuits are used in these analog switch ics. There are 3 circuits in this multiplexer. Search with 74LV4053 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 75Ohm. The functions of 16 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 5.5V to a switch device. A cost-effective Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 2V. For this digital switch to work, 20μA current would suffice. A voltage of 2V~5.5V is required to drain this analog switch from a single voltage supply. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. A 6 input needs to be operated. There are 50MHz bandwidths for data transfer. It is able to conduct in a 2-bit way. It belongs to the series Automotive, AEC-Q100. SN74LV4053ATDRQ1 Features 3 Channels Switch Circuit: SPDT 20μA Supply Current Bandwidth: 50MHz 2-Bit SN74LV4053ATDRQ1 Applications There are a lot of Texas Instruments SN74LV4053ATDRQ1 Analog Switches & Multiplexers ICs applications. Cross Connects Ultrasound Channel Banks Sample-and-hold systems Existing multiplexer applications (both fault-protected and nonfault-protected) Avionics test equipment Frame Relay Equipment Data Acquisition Systems Relay Replacement Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads	PDF	999 In-stock	Get Quote