Shine Ever will be exhibiting at ELECTRONICA in Munich Nov 12-15, 2024! COME VISIT US AT BOOTH 118/2, Hall C5
My CartGrounding Braid, Straps(2795)
| Image | Part | Manufacturer | Description | Stock | Action | |
|---|---|---|---|---|---|---|
| Texas Instruments | CD4051BPW OverviewShipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 8:1. Operating temperature around -55°C~125°C TA extended. Total terminations are 16. High-quality output is provided by the electronic component's 8 channels. With a 5V voltage supply, the electrical component should be turned on and run. An electrical component of this type can be found in the 16 series. A total of 1 circuits make up this switch device. CD4051 can be used to search for analog multiplexer variants. The internal resistance of this digital multiplexer is 240Ohm. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 20V should not normally be supplied to the switches. A cost-effective Dual, Single supply type analogue multiplexer. There should be 3V voltage fed to the electrical part below 3V. This multiplexer would work with 80nA current. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 9V. In the case of dual power supplies, you should connect at least 2.5V. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. This electrical part is compatible with 18V operating voltages. A 8 input needs to be operated. 20MHz-bandwidths can be used to transfer data between multiplexers. CD4051BPW Features8 Channels 80nA Supply Current Bandwidth: 20MHz CD4051BPW ApplicationsThere are a lot of Texas Instruments CD4051BPW Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4052PW OverviewAs the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 4:1. Operation at a temperature around -55°C~125°C TA. In total, there are 16 terminations. The electronic part delivers high-quality output through its 8 channels. Turning on and running the electrical part should be easy with a 4.5V voltage supply. An electrical component like this is included in the 16 series. A SP4T switching circuit is used for these analog switches. 2 circuits are used in this analogue multiplexer. Use 74HC4052 to search for variants of the digital switches. Analog switches have 130Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 6V voltage to the switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 2V should be applied to the electronic component. For this switch, a dual supply voltage is feasible, but it must not exceed 5VWith dual power supplies, you should attach at least 1V. There is an integrated analog IC DIFFERENTIAL MULTIPLEXER in the module. It is possible to transfer data over a 185MHz-bandwidth. There is 80Ohm resistance between the Drain and Source on this part. It is able to conduct in a 4-bit way. CD74HC4052PW Features8 Channels Switch Circuit: SP4T Bandwidth: 185MHz Drain-to-Source resistance: 80Ohm 4-Bit CD74HC4052PW ApplicationsThere are a lot of Texas Instruments CD74HC4052PW Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4051MM96EP OverviewThe electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. 8:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -55°C~125°C TA extended. There are 16 terminations totally. A electrical component with 8 channels is capable of high-quality output. When a voltage supply of 4.5V is used, the electronic component should be turned on and run. A total of 16 pins are injected into the electrical part body. A total of 1 circuits make up this switch device. Using the 74HC4051 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 130Ohm. Datasheets for 16 pin functions are available upon request. There is a standard Multiplexer or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 6V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 2V. If put voltage greater than 16μA on the device, damage may be caused to the analogue multiplexer. If put voltage greater than 5V on the multiplexer, damage may be caused to the device. You should attach at least 1V voltage if you are using dual power supply. This product is integrated with an analog integrated circuit (IC) of type SINGLE-ENDED MULTIPLEXER. In 180MHz-bandwidths, data can be transferred. CD74HC4051MM96EP Features8 Channels Bandwidth: 180MHz CD74HC4051MM96EP ApplicationsThere are a lot of Texas Instruments CD74HC4051MM96EP Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5N412PW OverviewThe electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. Advanced packaging method Tube is used to provide high reliability. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature extended to -40°C~85°C TA. 16 terminations have been made so far. The electronic part delivers high-quality output through its 4 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Based on SPDT switching circuits, these analog multiplexers work. It consists of 4 circuits. Using the TS5N412 search parameter, you can discover variants of the switch. A 12.5Ohm internal resistance characterizes this multiplexer. The datasheets for the 16 pins explain the functions. Users should never supply a voltage higher than 5.25V to a switch device. A analog switch ic that has a cost-effective Single supply type. In order for the electronic part to function properly, the lowest voltage should be 4.75V. This digital switch can be operated with a current of 10mA. This analogue multiplexer requires a voltage of 4.75V~5.25V when it drains from a single voltage supply. Operating voltages range from 5V. Among the inputs that can be operated are the 8 inputs. 25MHz bandwidths enable data to be transferred. Multiplexer ics with 4 outputs are available. TS5N412PW Features4 Channels Switch Circuit: SPDT 10mA Supply Current -3db Bandwidth: 25MHz Min Bandwidth: 25MHz TS5N412PW ApplicationsThere are a lot of Texas Instruments TS5N412PW Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | MPC509AU OverviewAs the electronic part is packed in 16-SOIC (0.295, 7.50mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tube is used. A switch device like this is mounted in Surface Mount. 4:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 2 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. There is an electrical component included in the 16 series. These analog multiplexers are built based on SP4T switching circuits. This multiplexer is composed of 2 circuits. Search with MPC509 if you are looking for analog multiplexer variants. Analog switches have 1.5kOhm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. A cost-effective Dual supply type analogue multiplexer. It would be sufficient to run this analogue multiplexer with 700μA current. There is no problem with using dual supply voltage, but it should not exceed 22V. If you are using a dual power supply, you should attach at least 5V. The electrical part can be operated at 18V voltage levels. There are 8 inputs to be operated. There are 1 outputs on the analogue multiplexer. MPC509AU Features2 Channels Switch Circuit: SP4T 700μA Supply Current MPC509AU ApplicationsThere are a lot of Texas Instruments MPC509AU Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| NXP Semiconductors | NX3L2467HR,115 OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 16-XFQFN Exposed Pad. The advanced packaging method Tape & Reel (TR) provides high reliability. This analog switch is mounted in Surface Mount. In the multiplexer and demultiplexer, 2:2 represents the number of circuits. Operational temperature extended around -40°C~125°C TA. The electronic part body is injected with 16 pins. A DPDT switching circuit is used to build these analog multiplexers. It consists of 2 circuits. NX3L2467 can be used to search for analog multiplexer variants. Using a single voltage supply, this switch device consumes 1.4V~4.3V volts. NX3L2467HR,115 FeaturesSwitch Circuit: DPDT -3db Bandwidth: 60MHz NX3L2467HR,115 ApplicationsThere are a lot of NXP USA Inc. NX3L2467HR,115 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LV4052AD OverviewPacked in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tube is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 4:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. There are 16 terminations totally. This electronic part offers high-quality output due to its 2 channels. In the case of a voltage supply of 2.5V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 16 series. The analog switch ics are built using SP4T switching circuits. The circuits in this analogue multiplexer number 2. Try searching with 74LV4052 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 100Ohm. The functions of 16 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 2V. For this digital switch to work, 20μA current would suffice. Using only a single voltage supply, this analog switch requires 2V~5.5V voltage. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. The electrical component supports 8 inputs. It is possible to transfer data over a 50MHz-bandwidth. There is 500Ohm Drain to Source resistance on this electronic part. It conducts in a 4-bit manner. SN74LV4052AD Features2 Channels Switch Circuit: SP4T 20μA Supply Current Bandwidth: 50MHz Drain-to-Source resistance: 500Ohm 4-Bit SN74LV4052AD ApplicationsThere are a lot of Texas Instruments SN74LV4052AD Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| NXP Semiconductors | NX3L1G53GM,125 OverviewAs the electronic part is packed in 8-XFQFN Exposed Pad, international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operation at a temperature around -40°C~125°C TA. A total of 8 terminations have been recorded. A 1 channel electronic part produces high-quality output. If the voltage supply is 1.65V volts, the electrical component should be turned on and run. It is part of the design of the 8 series that this electronic component is included. Based on SPDT switching circuits, these analog multiplexers work. The circuits in this analogue multiplexer number 1. Try searching for NX3L1G53G variants of the analog switch ic. A analogue multiplexer of this type is a Multiplexer or Switches. Draining from a single voltage supply, this analog switch requires a voltage of 1.4V~4.3V. NX3L1G53GM,125 Features1 Channels Switch Circuit: SPDT -3db Bandwidth: 60MHz NX3L1G53GM,125 ApplicationsThere are a lot of NXP USA Inc. NX3L1G53GM,125 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| NXP Semiconductors | NX3DV3899GU,115 OverviewPacked in 16-XFQFN, the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 2:2 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~125°C TA. There are 16 terminations totally. It is part of the design of the 16 series that this electronic component is included. On the other hand, analog switches can be constructed using DPDT switching circuits. Circuits number 2 make up this analogue multiplexer. If you are looking for variants of the digital switch, trying search with NX3DV3899. There is Multiplexer or Switches analog multiplexer like this in the world. Using only a single voltage supply, this analog switch requires 1.4V~4.3V voltage. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. NX3DV3899GU,115 FeaturesSwitch Circuit: DPDT -3db Bandwidth: 200MHz NX3DV3899GU,115 ApplicationsThere are a lot of NXP USA Inc. NX3DV3899GU,115 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4053M OverviewThe electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tube provides high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature extended to -55°C~125°C TA. There are 16 terminations totally. The electronic part provides high-quality output because it has 3 channels. When a voltage supply of 4.5V is used, the electronic component should be turned on and run. There is an electrical component included in the 16 series. Based on SPDT switching circuits, these analog multiplexers work. A 3 circuit is present in this switch device. Try searching for the analog switch ic with 74HCT4053 if you are looking for variants. It has an internal resistance of 130Ohm. For functions related to 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 5.5V voltage to the switch device. A cost-effective Dual, Single supply type analogue multiplexer. 4.5V should be the lowest voltage fed to the electronic component. Despite this switch's dual supply capability, its voltage should not exceed 5V. A dual power supply should have at least 1V voltage attached. Integrated with SINGLE-ENDED MULTIPLEXER analog IC. It can operate from 5V operating voltages. A 6 input needs to be operated. 200MHz bandwidths enable data to be transferred. It can conduct 2-bit signals. CD74HCT4053M Features3 Channels Switch Circuit: SPDT Bandwidth: 200MHz 2-Bit CD74HCT4053M ApplicationsThere are a lot of Texas Instruments CD74HCT4053M Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4051E OverviewShipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Through Hole. Multiplexers and demultiplexers have a ratio of 8:1. Operating temperature around -55°C~125°C TA extended. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. Powered by a 4.5V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 16 series. The multiplexer consists of 1 circuits. Try searching for the analog switch ic with 74HCT4051 if you are looking for variants. Analog switches have 180Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analog switch ics with Dual, Single supply type are cost-effective. A low voltage of 4.5V should be applied to the electronic component. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5V. When using dual power supplies, you should attach at least 1V. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. Operating voltages of 5V are compatible with the electrical part. A 8 input needs to be operated. In 180MHz-bandwidths, data can be transferred. CD74HCT4051E Features1 Channels Bandwidth: 180MHz CD74HCT4051E ApplicationsThere are a lot of Texas Instruments CD74HCT4051E Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4066M OverviewThis electronic part is conveniently packaged in 14-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Surface Mount, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -55°C~125°C TA. The total number of terminations is 14. By its 4 channels, the electronic component provides high-quality output. In the case of a voltage supply of 4.5V volts, the electrical part can be powered up and run. It is part of the design of the 14 series that this electronic component is included. A SPST - NO switching circuit is used to build these analog multiplexers. Search with 74HC4066 if you are looking for analog multiplexer variants. Analog switches have 70Ohm internal resistance. For details about the functions of 14 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 10V in normal situations. An effective Single supply digital multiplexer. 2V is the lowest voltage the electrical component should receive. Using a single voltage supply, this switch device consumes 2V~10V volts. It may damage the digital multiplexer if the voltage is higher than 16μA. This switch operates within the bandwidth of 200MHz. Drain to Source resistance for this electronic component is 25Ohm. CD74HC4066M Features4 Channels Switch Circuit: SPST - NO Bandwidth: 200MHz Drain-to-Source resistance: 25Ohm CD74HC4066M ApplicationsThere are a lot of Texas Instruments CD74HC4066M Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4051M OverviewThis electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is ensured by the advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 8:1 represents the number of circuits. Operational temperature extended around -55°C~125°C TA. In total, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 4.5V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. This multiplexer is composed of 1 circuits. Try searching with 74HC4051 if you're looking for variants. Internally, this switch multiplexer has a resistance of 160Ohm. You can find the functions of the 16 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage the electronic part should receive is 2V. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 5V. With dual power supplies, you should attach at least 1V. This product is integrated with an analog integrated circuit (IC) of type SINGLE-ENDED MULTIPLEXER. Operating the 8 inputs requires 8 inputs. The data can be transferred over a wide range of bandwidths, called 180MHz bandwidths. There is 40Ohm Drain to Source resistance on this electronic part. CD74HC4051M Features1 Channels Bandwidth: 180MHz Drain-to-Source resistance: 40Ohm CD74HC4051M ApplicationsThere are a lot of Texas Instruments CD74HC4051M Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4052M OverviewAs the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Surface Mount. 4:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -55°C~125°C TA. There are 16 terminations totally. A high-quality output is provided by the electrical component's 8 channels. Turning on and running the electrical part should be easy with a 4.5V voltage supply. The electrical component body receives 16 pins. Based on SP4T switching circuits, these analog multiplexers work. The circuits in this analogue multiplexer number 2. 74HC4052 can be used to search for analog multiplexer variants. This digital multiplexer has 160Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 6V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 2V voltage fed to the electrical part below 2V. For this multiplexer, dual supply voltage is feasible, but it should not exceed 5V. A dual power supply should have at least 1V voltage attached. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. A 185MHz-bandwidth can be used for data transfer. A Drain to Source resistance of 40Ohm is shown for this electronic part. 4-bit operation is possible. CD74HC4052M Features8 Channels Switch Circuit: SP4T Bandwidth: 185MHz Drain-to-Source resistance: 40Ohm 4-Bit CD74HC4052M ApplicationsThere are a lot of Texas Instruments CD74HC4052M Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LV4051AN OverviewPresented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. In Through Hole, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. Operating temperature around -40°C~85°C TA extended. In total, 16 terminations have occurred. High-quality output is provided by the electronic component's 8 channels. With a 2.3V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. This multiplexer is composed of 1 circuits. Look for analog switch ic variants by searching with 74LV4051. In this multiplexer, the internal resistance is 75Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 5.5V should not normally be supplied to the switches. An effective Single supply digital multiplexer. The lowest voltage the electronic part should receive is 2V. 20μA current would be enough for this multiplexer to operate. Using a single voltage supply, this switch device consumes 2V~5.5V volts. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. A 8 input needs to be operated. This switch operates within the bandwidth of 35MHz. This electronic component presents a Drain to Source resistance of 100Ohm. SN74LV4051AN Features8 Channels 20μA Supply Current Bandwidth: 35MHz Drain-to-Source resistance: 100Ohm SN74LV4051AN ApplicationsThere are a lot of Texas Instruments SN74LV4051AN Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Microchip Technology | HV2621/R4X OverviewDue to its 64-VFQFN Exposed Pad packaging, the electronic part is convenient for international shipping. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Extended operating temperature around 0°C~70°C TA. In total, there are 64 terminations. The electronic part provides high-quality output because it has 1 channels. With a 5V voltage supply, the electrical component should be turned on and run. On the other hand, analog switches can be constructed using SPST switching circuits. There are 1 circuits in this multiplexer. A voltage of 3V~5.5V is required to drain this analog switch from a single voltage supply. HV2621/R4X Features1 Channels Switch Circuit: SPST HV2621/R4X ApplicationsThere are a lot of Microchip Technology HV2621/R4X Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| NXP Semiconductors | NX3L1T3157GM,115 OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 6-XFDFN. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~125°C TA. Total terminations are 6. The electronic part provides high-quality output because it has 1 channels. With a 1.65V voltage supply, the electrical component should be turned on and run. The electronic part body is injected with 6 pins. Based on SPDT switching circuits, these analog multiplexers work. Circuits number 1 make up this analogue multiplexer. Try searching for NX3L1T3157G variants of the analog switch ic. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage of 1.4V~4.3V is required for this switch device, which drains from a single voltage source. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. NX3L1T3157GM,115 Features1 Channels Switch Circuit: SPDT -3db Bandwidth: 60MHz NX3L1T3157GM,115 ApplicationsThere are a lot of NXP USA Inc. NX3L1T3157GM,115 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments |
240
In-stock
|
Get Quote | ||||
| Texas Instruments | SN74LVC1G3157DTBR OverviewDue to its 6-XFDFN packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. There is 2:1 ratio between the number of multiplexers and demultiplexers. Temperatures around -40°C~125°C TA are extended for operation. 6 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. Based on SPDT switching circuits, these analog multiplexers work. The multiplexer consists of 1 circuits. Try searching for 74LVC1G3157 variants of the analog switch ic. You can find the functions of the 6 pins in the datasheets. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. There are various bandwidths available for data transfer. SN74LVC1G3157DTBR Features1 Channels Switch Circuit: SPDT -3db Bandwidth: 340MHz Bandwidth: 340MHz SN74LVC1G3157DTBR ApplicationsThere are a lot of Texas Instruments SN74LVC1G3157DTBR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A4597DBVR OverviewShipping overseas is convenient due to the electrical component's packing in SC-74A, SOT-753. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around -40°C~85°C TA. In total, 5 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. The electronic part body is injected with 5 pins. Unlike digital switches, these are based on SPST - NC switching circuits. Try searching for TS5A4597 variants of the analog switch ic. Analog switches have 8Ohm internal resistance. Datasheets for functions of 5 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. 2V should be the lowest voltage fed to the electronic component. 10nA current would be enough for this multiplexer to operate. Analogue multiplexers require a 2V~5.5V voltage to drain from a single voltage supply. If you put voltage higher than 250nA on the digital multiplexer, damage may occur. It is possible to transfer data over a 450MHz-bandwidth. TS5A4597DBVR Features1 Channels Switch Circuit: SPST - NC 10nA Supply Current Bandwidth: 450MHz TS5A4597DBVR ApplicationsThere are a lot of Texas Instruments TS5A4597DBVR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A3157DBVR OverviewThe electronic part can be shipped overseas conveniently because it is packaged in SOT-23-6. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature extended to -40°C~85°C TA. 6 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 1.8V voltage supply. Into the electrical component body are injected 6 pins. A SPDT switching circuit is used to build these analog multiplexers. TS5A3157 can be used to search for analog multiplexer variants. A 10Ohm internal resistance characterizes this multiplexer. To find out what the 6 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. 1.65V should be the lowest voltage fed to the electronic component. This digital switch can be operated with a current of 2.5μA. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 5μA. 300MHz-bandwidths can be used to transfer data between multiplexers. Don't miss this electronic component's additional features, such as: VIDEO APPLICATION. Resistivity from Drain to Source is 12Ohm for this electronic part. 2 outputs are included in the analogue multiplexer. TS5A3157DBVR Features1 Channels Switch Circuit: SPDT 2.5μA Supply Current Bandwidth: 300MHz Additional Features: VIDEO APPLICATION Drain-to-Source resistance: 12Ohm TS5A3157DBVR ApplicationsThere are a lot of Texas Instruments TS5A3157DBVR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4053M96 OverviewShipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Cut Tape (CT) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Operating temperature around -55°C~125°C TA extended. The total number of terminations is 16. As a result of its 2 channels, this electronic component provides high-quality output. An 4.5V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 16 pins. These analog multiplexers are built based on SPDT switching circuits. This multiplexer is composed of 3 circuits. Look for analog switch ic variants by searching with 74HC4053. A 130Ohm internal resistance characterizes this multiplexer. To find out what the 16 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 6V volts for the multiplexer. Dual, Single supply type digital switch with a low cost. 2V should be the lowest voltage fed to the electronic component. The switch device would be able to operate with 160μA current. If put voltage greater than 5V on the multiplexer, damage may be caused to the device. With dual power supplies, you should attach at least 1V. This product is integrated with an analog integrated circuit (IC) of type SINGLE-ENDED MULTIPLEXER. Operating 6 inputs is required. The transfer of data can be performed over 200MHz bandwidths. There is 130mOhm resistance between Drain and Source for this electronic part. CD74HC4053M96 Features2 Channels Switch Circuit: SPDT 160μA Supply Current Bandwidth: 200MHz Drain-to-Source resistance: 130mOhm CD74HC4053M96 ApplicationsThere are a lot of Texas Instruments CD74HC4053M96 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4051M96 OverviewDue to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Cut Tape (CT) is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 8:1. Operating temperature extended to -55°C~125°C TA. Total terminations are 16. As a result of its 1 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 4.5V voltage supply. It is injected into the electrical part body with 16 pins. The circuits in this analogue multiplexer number 1. If you are looking for variants of the digital switch, trying search with 74HCT4051. Internally, this switch multiplexer has a resistance of 130Ohm. The functions of 16 pins can be found in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Dual, Single supply type digital switch with a low cost. 4.5V is the lowest voltage that should be fed to the electronic electronic part. It would be sufficient to run this analogue multiplexer with 160μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5V. For dual power supplies, a voltage of at least 1V should be attached. With a SINGLE-ENDED MULTIPLEXER analog IC integrated into the board. The electrical part can be operated at 5V voltage levels. It is possible to operate 8 inputs. This switch operates within the bandwidth of 180MHz. CD74HCT4051M96 Features1 Channels 160μA Supply Current Bandwidth: 180MHz CD74HCT4051M96 ApplicationsThere are a lot of Texas Instruments CD74HCT4051M96 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4066M96 OverviewShipping overseas is convenient with the electronic component packed in 14-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Cut Tape (CT). Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -55°C~125°C TA. Totally, there are 14 terminations. Due to its 4 channels, the electrical component produces high-quality output. An 4.5V voltage supply should allow the electrical part to be turned on and run. A total of 14 pins are injected into the body of the electronic part. SPST - NO switching circuits are used in these analog switch ics. Use 74HC4066 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 70Ohm. Datasheets for functions of 14 pins are available. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 10V. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 2V. Using a single voltage supply, this switch device consumes 2V~10V volts. The switch multiplexer may be damaged if it is exposed to voltage greater than 40μA. There are 200MHz bandwidths for data transfer. A Drain to Source resistance of 70Ohm is shown for this electronic part. CD74HC4066M96 Features4 Channels Switch Circuit: SPST - NO Bandwidth: 200MHz Drain-to-Source resistance: 70Ohm CD74HC4066M96 ApplicationsThere are a lot of Texas Instruments CD74HC4066M96 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A63157DCKR OverviewAs the electronic part is packed in 6-TSSOP, SC-88, SOT-363, international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 6. A 1 channel electronic part produces high-quality output. A 1.8V voltage supply should turn on and run the electronic component. An injection of 6 pins is performed into the body of the electrical component. Multiplexers built on a SPDT switching circuit are built. Try searching with TS5A63157 to find analog multiplexer variants. In this multiplexer, the internal resistance is 12Ohm. To find out what the 6 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 5.5V to a switch device. The analog switch ic is of the Single supply type and is cost-effective. It is recommended to use 1.65V as the lowest voltage for the electrical part. The analogue multiplexer could operate on 10nA current. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 100nA. There are 2 inputs to be operated. This switch operates within the bandwidth of 370MHz. Drain to Source resistance for this electronic component is 12Ohm. TS5A63157DCKR Features1 Channels Switch Circuit: SPDT 10nA Supply Current -3db Bandwidth: 371MHz Bandwidth: 370MHz Drain-to-Source resistance: 12Ohm TS5A63157DCKR ApplicationsThere are a lot of Texas Instruments TS5A63157DCKR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4053M96 OverviewShipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Temperatures around -55°C~125°C TA are extended for operation. Total terminations are 16. High-quality output is provided by the electronic component's 3 channels. When the electronic component is given a voltage of 4.5V, it should be turned on and run. As part of its design, the 16 series is equipped with this electronic component. Based on SPDT switching circuits, these analog multiplexers work. 3 circuits are used in this analogue multiplexer. Try searching with 74HCT4053 to find analog multiplexer variants. There is 130Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage the electronic part should receive is 4.5V. Despite this switch's dual supply capability, its voltage should not exceed 5V. In the case of dual power supplies, you should connect at least 1V. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. Operating voltages of 5V are compatible with the electrical part. It is possible to operate 6 inputs. 200MHz-bandwidths can be used to transfer data between multiplexers. 2-bits are supported. CD74HCT4053M96 Features3 Channels Switch Circuit: SPDT Bandwidth: 200MHz 2-Bit CD74HCT4053M96 ApplicationsThere are a lot of Texas Instruments CD74HCT4053M96 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4053PWR OverviewThe electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). To ensure high reliability, a new packaging method Cut Tape (CT) is used. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature around -55°C~125°C TA extended. The total number of terminations is 16. A high-quality output is provided by the electrical component's 3 channels. Powered by a 4.5V voltage supply, the electrical part should be switched on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. These analog multiplexers are built based on SPDT switching circuits. This multiplexer is composed of 3 circuits. Try searching for the analog switch ic with 74HCT4053 if you are looking for variants. It has an internal resistance of 130Ohm. To find out what the 16 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Analogue multiplexer with a Dual, Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 4.5V. If put voltage greater than 5V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 1V. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. Operating voltages range from 5V. A 6 input needs to be operated. There are 200MHz bandwidths for data transfer. 2-bits are supported. CD74HCT4053PWR Features3 Channels Switch Circuit: SPDT Bandwidth: 200MHz 2-Bit CD74HCT4053PWR ApplicationsThere are a lot of Texas Instruments CD74HCT4053PWR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A63157DBVR OverviewShipping overseas is convenient with the electronic component packed in SOT-23-6. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature around -40°C~85°C TA extended. The total number of terminations is 6. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 1.8V, it should be turned on and run. As part of the design of the 6 series, this electronic part has been incorporated into the system. A SPDT switching circuit is used for these analog switches. Search with TS5A63157 if you are looking for analog multiplexer variants. A 10Ohm internal resistance characterizes this multiplexer. The datasheets for the 6 pins explain the functions. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. A analog switch ic that has a cost-effective Single supply type. 1.65V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 10nA. The voltage required by this switch device is 1.65V~5.5V, draining from a single voltage supply. Putting voltage greater than 100nA on the multiplexer may cause damage. Operating the 2 inputs requires 2 inputs. The data can be transferred over a wide range of bandwidths, called 370MHz bandwidths. A Drain to Source resistance of 12Ohm is shown for this electronic part. TS5A63157DBVR Features1 Channels Switch Circuit: SPDT 10nA Supply Current -3db Bandwidth: 371MHz Bandwidth: 370MHz Drain-to-Source resistance: 12Ohm TS5A63157DBVR ApplicationsThere are a lot of Texas Instruments TS5A63157DBVR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LVC2G66QDCURQ1 OverviewShipping overseas is convenient with the electronic component packed in 8-VFSOP (0.091, 2.30mm Width). To ensure high reliability, a new packaging method Cut Tape (CT) is used. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~125°C TA. Total terminations are 8. Due to its 2 channels, the electrical component produces high-quality output. If the voltage supply is 3.3V volts, the electrical component should be turned on and run. The electrical component body receives 8 pins. These analog multiplexers are built based on SPST - NO switching circuits. Using the 74LVC2G66 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 15Ohm. The functions of 8 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A analog switch ic that has a cost-effective Single supply type. 1.65V is the lowest voltage that should be fed to the electronic electronic part. In order to operate this switch device, it would need a current of 15μA. The voltage required by this switch device is 1.65V~5.5V, draining from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 100nA. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. 300MHz bandwidths enable data to be transferred. The Automotive, AEC-Q100 series is responsible for it. SN74LVC2G66QDCURQ1 Features2 Channels Switch Circuit: SPST - NO 15μA Supply Current -3db Bandwidth: 300MHz Bandwidth: 300MHz SN74LVC2G66QDCURQ1 ApplicationsThere are a lot of Texas Instruments SN74LVC2G66QDCURQ1 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A23166YZPR OverviewPresented in 8-XFBGA, DSBGA, this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there are 8 terminations. A 2 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 1.8V voltage supply. As part of the design of the 8 series, this electronic part has been incorporated into the system. The analog switch ics are built using SPST - NO switching circuits. Try searching with TS5A23166 to find analog multiplexer variants. There is 900mOhm internal resistance in this digital multiplexer. To find out what the 8 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 1.65V. An operating current of 10nA would be sufficient for this switch device. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. When the digital multiplexer is charged above 100nA, damage can occur. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. The transfer of data can be performed over 150MHz bandwidths. TS5A23166YZPR Features2 Channels Switch Circuit: SPST - NO 10nA Supply Current Bandwidth: 150MHz TS5A23166YZPR ApplicationsThere are a lot of Texas Instruments TS5A23166YZPR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote |
Please send RFQ , we will respond immediately.
