Shine Ever will be exhibiting at ELECTRONICA in Munich Nov 12-15, 2024! COME VISIT US AT BOOTH 118/2, Hall C5
My CartGrounding Braid, Straps(2795)
| Image | Part | Manufacturer | Description | Stock | Action | |
|---|---|---|---|---|---|---|
| Texas Instruments | TS3A5017PWR OverviewThis electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 4:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 4 channels. Powered by a 2.5V voltage supply, the electrical part should be switched on and run. A total of 16 pins are injected into the body of the electronic part. The analog switch ics are built using SP4T switching circuits. This multiplexer is composed of 2 circuits. Try searching for the analog switch ic with TS3A5017 if you are looking for variants. This digital multiplexer has 12Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. A voltage higher than 3.6V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. There should be 2.3V voltage fed to the electrical part below 2.3V. It would be sufficient to run this analogue multiplexer with 2.5μA current. An analogue multiplexer drains from a single voltage supply at 2.3V~3.6V. Putting voltage greater than 7μA on the multiplexer may cause damage. It is possible to transfer data over a 165MHz-bandwidth. The Drain to Source resistance of this electronic component is 12Ohm. Multiplexer ics with 8 outputs are available. TS3A5017PWR Features4 Channels Switch Circuit: SP4T 2.5μA Supply Current Bandwidth: 165MHz Drain-to-Source resistance: 12Ohm TS3A5017PWR ApplicationsThere are a lot of Texas Instruments TS3A5017PWR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A23166YZTR OverviewDue to its 8-UFBGA, DSBGA packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature extended to -40°C~85°C TA. Total terminations are 8. By its 2 channels, the electronic component provides high-quality output. When a voltage supply of 1.8V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 8 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching with TS5A23166 to find analog multiplexer variants. Analog switches have 900mOhm internal resistance. To find out what the 8 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The digital multiplexer has a low cost Single supply. A low voltage of 1.65V should be applied to the electronic component. For this multiplexer to operate, 10nA current would be sufficient. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. A voltage higher than 100nA may cause damage to the switch multiplexer. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. This switch operates within the bandwidth of 150MHz. TS5A23166YZTR Features2 Channels Switch Circuit: SPST - NO 10nA Supply Current Bandwidth: 150MHz TS5A23166YZTR ApplicationsThere are a lot of Texas Instruments TS5A23166YZTR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| NXP Semiconductors | NX3L2267GU,115 OverviewThis electronic part is conveniently packaged in 10-XFQFN, making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Temperatures around -40°C~125°C TA are extended for operation. Totally, there are 10 terminations. An electrical component of this type can be found in the 10 series. Based on SPDT switching circuits, these analog multiplexers work. A 2 circuit is present in this switch device. If you are looking for variants of the digital switch, trying search with NX3L2267. In this analog multiplexer, the value is Multiplexer or Switches. This analog switch requires a voltage of 1.4V~4.3V to drain from a single voltage supply. This analog switch ic utilizes SEPARATE OUTPUT output. NX3L2267GU,115 FeaturesSwitch Circuit: SPDT -3db Bandwidth: 60MHz NX3L2267GU,115 ApplicationsThere are a lot of NXP USA Inc. NX3L2267GU,115 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LV4051ANSR OverviewPresented in 16-SOIC (0.209, 5.30mm Width), this electrical component is convenient for overseas shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. There is 8:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. A total of 16 terminations have been recorded. By its 8 channels, the electronic component provides high-quality output. A 2.3V voltage supply should turn on and run the electronic component. Electronic part bodies are injected with 16 pins. Circuits number 1 make up this analogue multiplexer. 74LV4051 can be used to search for analog multiplexer variants. It has an internal resistance of 75Ohm. For functions related to 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 5.5V to a switch device. Analogue multiplexer with a Single supply type that is cost-effective. 2V should be the lowest voltage fed to the electronic component. For this digital switch to work, 20μA current would suffice. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. A 8 input needs to be operated. There are various bandwidths available for data transfer. SN74LV4051ANSR Features8 Channels 20μA Supply Current Bandwidth: 35MHz SN74LV4051ANSR ApplicationsThere are a lot of Texas Instruments SN74LV4051ANSR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TMUX1122DGKR OverviewThis electronic part is conveniently packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature extended to -40°C~125°C TA. In total, 8 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. When a voltage supply of 1.2V is used, the electronic component should be turned on and run. Based on SPST switching circuits, these analog multiplexers work. There are 2 circuits in this switch device. Try searching with TMUX1122 to find analog multiplexer variants. A voltage of 1.08V~5.5V is required for this switch device, which drains from a single voltage source. There are various bandwidths available for data transfer. TMUX1122DGKR Features1 Channels Switch Circuit: SPST -3db Bandwidth: 300MHz Bandwidth: 300MHz TMUX1122DGKR ApplicationsThere are a lot of Texas Instruments TMUX1122DGKR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TMUX1104DQAR OverviewPacked in 10-UFDFN, the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In the multiplexer and demultiplexer, 4:1 represents the number of circuits. Increasing operating temperature to around -40°C~125°C TA. Total terminations are 10. A 2 channel electronic part produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. A SP4T switching circuit is used to build these analog multiplexers. There are 1 circuits in this multiplexer. If you are looking for variants of the digital switch, trying search with TMUX1104. Draining from a single voltage supply, this analog switch requires a voltage of 1.08V~5.5V. This product is integrated with an analog integrated circuit (IC) of type SINGLE-ENDED MULTIPLEXER. This switch operates within the bandwidth of 150MHz. TMUX1104DQAR Features2 Channels Switch Circuit: SP4T -3db Bandwidth: 155MHz Bandwidth: 150MHz TMUX1104DQAR ApplicationsThere are a lot of Texas Instruments TMUX1104DQAR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TMUX1111PWR OverviewDue to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around -40°C~125°C TA. A total of 16 terminations have been recorded. A high-quality output is provided by the electrical component's 1 channels. In the case of a voltage supply of 1.2V volts, the electrical part can be powered up and run. Based on SPST switching circuits, these analog multiplexers work. Circuits number 4 make up this analogue multiplexer. Using the TMUX1111 search parameter, you can discover variants of the switch. Analogue multiplexers require a 1.08V~5.5V voltage to drain from a single voltage supply. In 400MHz-bandwidths, data can be transferred. TMUX1111PWR Features1 Channels Switch Circuit: SPST -3db Bandwidth: 300MHz Bandwidth: 400MHz TMUX1111PWR ApplicationsThere are a lot of Texas Instruments TMUX1111PWR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TMUX1113PWR OverviewShipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Multiplexer and demultiplexer circuits have a number 1:1. Around -40°C~125°C TA is the extended operating temperature. Total terminations are 16. By its 1 channels, the electronic component provides high-quality output. When a voltage supply of 1.2V is used, the electronic component should be turned on and run. SPST switching circuits are used in these analog switch ics. There are 4 circuits in this multiplexer. Try searching with TMUX1113 to find analog multiplexer variants. Analogue multiplexers require a 1.08V~5.5V voltage to drain from a single voltage supply. The data can be transferred over a wide range of bandwidths, called 400MHz bandwidths. TMUX1113PWR Features1 Channels Switch Circuit: SPST -3db Bandwidth: 300MHz Bandwidth: 400MHz TMUX1113PWR ApplicationsThere are a lot of Texas Instruments TMUX1113PWR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TMUX6121DGSR OverviewThe electrical component comes in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. The advanced packaging method Cut Tape (CT) provides high reliability. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~125°C TA. Total terminations are 10. As a result of its 1 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. Based on SPST switching circuits, these analog multiplexers work. It consists of 2 circuits. Try searching with TMUX6121 if you're looking for variants. 630MHz bandwidths enable data to be transferred. To supply the switch device, a voltage of 5V must be applied. TMUX6121DGSR Features1 Channels Switch Circuit: SPST -3db Bandwidth: 630MHz Bandwidth: 630MHz TMUX6121DGSR ApplicationsThere are a lot of Texas Instruments TMUX6121DGSR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TMUX1108PWR OverviewShipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Cut Tape (CT) is used. The multiplexer is located in Surface Mount. There is 8:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~125°C TA. In total, 16 terminations have occurred. This electronic part offers high-quality output due to its 1 channels. It consists of 1 circuits. Try searching with TMUX1108 if you're looking for variants. Using only a single voltage supply, this analog switch requires 1.08V~5.5V voltage. With a SINGLE-ENDED MULTIPLEXER analog IC integrated into the board. It is possible to transfer data over a 90MHz-bandwidth. TMUX1108PWR Features1 Channels -3db Bandwidth: 90MHz Bandwidth: 90MHz TMUX1108PWR ApplicationsThere are a lot of Texas Instruments TMUX1108PWR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | MUX506IPWR OverviewPacked in 28-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. 16:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~125°C TA. The total number of terminations is 28. The electronic part delivers high-quality output through its 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. The circuits in this analogue multiplexer number 1. If you are looking for variants of the digital switch, trying search with MUX506. For functions related to 28 pins, please refer to the datasheets. Integrated with DIFFERENTIAL MULTIPLEXER analog IC. COMMON OUTPUT outputs are utilized by this digital multiplexer. 500MHz-bandwidths can be used to transfer data between multiplexers. MUX506IPWR Features1 Channels Bandwidth: 500MHz MUX506IPWR ApplicationsThere are a lot of Texas Instruments MUX506IPWR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | MUX507IDWR OverviewThe electronic component is convenient to ship overseas because it is packed in a 28-SOIC (0.295, 7.50mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 8:1. Around -40°C~125°C TA is the extended operating temperature. In total, 28 terminations have occurred. The electronic part provides high-quality output because it has 2 channels. A 15V voltage supply should turn on and run the electronic component. There are 2 circuits in this multiplexer. Try searching for the analog switch ic with MUX507 if you are looking for variants. To find out what the functions of 28 pins are, please refer to their datasheets. Integrated with DIFFERENTIAL MULTIPLEXER analog IC. COMMON OUTPUT outputs are utilized by this digital multiplexer. In 500MHz-bandwidths, data can be transferred. MUX507IDWR Features2 Channels Bandwidth: 500MHz MUX507IDWR ApplicationsThere are a lot of Texas Instruments MUX507IDWR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TMUX6112PWR OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. There is 2:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -40°C~125°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. A SPDT switching circuit is used to build these analog multiplexers. A 1 circuit is present in this switch device. Use TMUX6112 to search for variants of the digital switches. With a SPST analog IC integrated into the board. The data can be transferred over a wide range of bandwidths, called 800MHz bandwidths. TMUX6112PWR Features1 Channels Switch Circuit: SPDT -3db Bandwidth: 800MHz Bandwidth: 800MHz TMUX6112PWR ApplicationsThere are a lot of Texas Instruments TMUX6112PWR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | MUX36S08IRRJR OverviewPresented in 16-WQFN Exposed Pad, this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. There is 8:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~125°C TA extended. There are 16 terminations totally. A high-quality output is provided by the electrical component's 8 channels. With a 15V voltage supply, the electrical component should be turned on and run. The multiplexer consists of 1 circuits. Try searching with 36S08 if you're looking for variants. Integrated with SINGLE-ENDED MULTIPLEXER analog IC. The data can be transferred over a wide range of bandwidths, called 500MHz bandwidths. MUX36S08IRRJR Features8 Channels Bandwidth: 500MHz MUX36S08IRRJR ApplicationsThere are a lot of Texas Instruments MUX36S08IRRJR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | MUX36D08IRTVR OverviewThe electronic component is convenient to ship overseas because it is packed in a 32-WFQFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. There is 8:1 ratio between the number of multiplexers and demultiplexers. Temperatures around -40°C~125°C are extended for operation. A total of 32 terminations have been recorded. Due to its 8 channels, the electrical component produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. This multiplexer is composed of 2 circuits. Use 36D08 to search for variants of the digital switches. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. The transfer of data can be performed over 500MHz bandwidths. MUX36D08IRTVR Features8 Channels Bandwidth: 500MHz MUX36D08IRTVR ApplicationsThere are a lot of Texas Instruments MUX36D08IRTVR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | MPC506AU OverviewThis electronic part is conveniently packaged in 28-SOIC (0.295, 7.50mm Width), making it easy to ship abroad. High reliability is provided by advanced packaging method Tube. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 16:1. Temperatures around -40°C~85°C TA are extended for operation. In total, 28 terminations have occurred. Due to its 16 channels, the electrical component produces high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. It is injected into the electrical part body with 28 pins. There are 1 circuits in this multiplexer. Try searching with MPC506 to find analog multiplexer variants. The internal resistance of this digital multiplexer is 1.5kOhm. For details about the functions of 28 pins, please refer to the datasheets. The analog switch ic is of the Dual supply type and is cost-effective. For this multiplexer to operate, 700μA current would be sufficient. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. It is recommended that you attach at least 5V to your dual power supply. It can operate from 18V operating voltages. A Drain to Source resistance of 1.5kOhm is shown for this electronic part. MPC506AU Features16 Channels 700μA Supply Current Drain-to-Source resistance: 1.5kOhm MPC506AU ApplicationsThere are a lot of Texas Instruments MPC506AU Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4053E OverviewThe electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. In Through Hole, you'll find this switch device. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -55°C~125°C TA. Totally, there are 16 terminations. A high-quality output is provided by the electrical component's 2 channels. If the voltage supply is 4.5V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the electrical part body. Unlike digital switches, these are based on SPDT switching circuits. Circuits number 3 make up this analogue multiplexer. If you are looking for variants of the digital switch, trying search with 74HC4053. In this multiplexer, the internal resistance is 160Ohm. To find out what the 16 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 6V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. If put voltage greater than 5V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 1V. With a SINGLE-ENDED MULTIPLEXER analog IC integrated into the board. Among the inputs that can be operated are the 6 inputs. 200MHz bandwidths enable data to be transferred. A Drain to Source resistance of 160Ohm is shown for this electronic part. CD74HC4053E Features2 Channels Switch Circuit: SPDT Bandwidth: 200MHz Drain-to-Source resistance: 160Ohm CD74HC4053E ApplicationsThere are a lot of Texas Instruments CD74HC4053E Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | MPC509AP OverviewPacked in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tube. This analog switch is mounted in Through Hole. Multiplexers and demultiplexers have the same number of circuits 4:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. A 2 channel electronic part produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 16 pins. Unlike digital switches, these are based on SP4T switching circuits. There are 2 circuits in this switch device. If you are looking for variants of the digital switch, trying search with MPC509. Analog switches have 1.5kOhm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. Analogue multiplexer with a Dual supply type that is cost-effective. 700μA current would be enough for this multiplexer to operate. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. For dual power supplies, a voltage of at least 5V should be attached. The electronic component can function from 18V. Operating 8 inputs is required. There is 1.3kOhm resistance between the Drain and Source on this part. The analog switch ics includes 1 outputs. MPC509AP Features2 Channels Switch Circuit: SP4T 700μA Supply Current Drain-to-Source resistance: 1.3kOhm MPC509AP ApplicationsThere are a lot of Texas Instruments MPC509AP Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4066E OverviewThe electronic component is convenient to ship overseas because it is packed in a 14-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. Extended operating temperature around -55°C~125°C TA. In total, 14 terminations have occurred. By its 4 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 4.5V voltage supply. An electrical component of this type can be found in the 14 series. These analog multiplexers are built based on SPST - NO switching circuits. Use 74HCT4066 to search for variants of the digital switches. An switch multiplexer with 95Ohm internal resistance has a value of 95Ohm. For details about the functions of 14 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. Single supply type digital switch with a low cost. 4.5V should be the lowest voltage fed to the electronic component. This analog switch requires a voltage of 4.5V~5.5V to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 2μA. 5V operating voltages are supported by the electronic component. The transfer of data can be performed over 200MHz bandwidths. The Drain to Source resistance of this electronic component is 95Ohm. CD74HCT4066E Features4 Channels Switch Circuit: SPST - NO Bandwidth: 200MHz Drain-to-Source resistance: 95Ohm CD74HCT4066E ApplicationsThere are a lot of Texas Instruments CD74HCT4066E Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD4097BM OverviewPresented in 24-SOIC (0.295, 7.50mm Width), this electrical component is convenient for overseas shipping. The advanced packaging method Tube provides high reliability. This analog switch is mounted in Surface Mount. There is 8:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -55°C~125°C TA degrees Celsius. Totally, there are 24 terminations. Due to its 2 channels, the electrical component produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. An electrical component like this is included in the 24 series. A total of 2 circuits make up this switch device. Try searching for CD4097 variants of the analog switch ic. This digital multiplexer has 240Ohm internal resistance. To find out what the functions of 24 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 18V. An effective Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 3V. The switch device would be able to operate with 80nA current. A voltage of 3V~18V is required to drain this analog switch from a single voltage supply. It is integrated with a DIFFERENTIAL MULTIPLEXER analog IC. Operating the 16 inputs requires 16 inputs. 20MHz bandwidths enable data to be transferred. There is 125Ohm Drain to Source resistance on this electronic part. It is able to conduct in a 8-bit way. CD4097BM Features2 Channels 80nA Supply Current Bandwidth: 20MHz Drain-to-Source resistance: 125Ohm 8-Bit CD4097BM ApplicationsThere are a lot of Texas Instruments CD4097BM Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4052M OverviewPacked in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tube is used. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 4:1 represents the number of circuits. The operating temperature is extended to around -55°C~125°C TA. In total, there are 16 terminations. High-quality output is provided by the electronic component's 2 channels. If the voltage supply is 4.5V volts, the electrical component should be turned on and run. As part of its design, the 16 series is equipped with this electronic component. Based on SP4T switching circuits, these analog multiplexers work. There are 2 circuits in this multiplexer. 74HCT4052 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 180Ohm. For details about the functions of 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. 4.5V is the lowest voltage the electrical component should receive. Despite this switch's dual supply capability, its voltage should not exceed 5V. If you are using dual power supplies, you should attach at least 1V. It is integrated with a DIFFERENTIAL MULTIPLEXER analog IC. The electrical part can be operated at 5V voltage levels. There are 8 inputs to be operated. There are 185MHz bandwidths for data transfer. It has a Drain to Source resistance of 40Ohm ohms. Its conductivity is 4-bit. CD74HCT4052M Features2 Channels Switch Circuit: SP4T Bandwidth: 185MHz Drain-to-Source resistance: 40Ohm 4-Bit CD74HCT4052M ApplicationsThere are a lot of Texas Instruments CD74HCT4052M Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A23160DGST OverviewThe electrical component comes in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. In total, there have been 10 terminations. A high-quality output is provided by the electrical component's 2 channels. With a 1.8V voltage supply, the electrical component should be turned on and run. An electrical component of this type can be found in the 10 series. A SPDT switching circuit is used for these analog switches. Try searching with TS5A23160 to find analog multiplexer variants. As far as internal resistance is concerned, it has 900mOhm. For details about the functions of 10 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 1.65V. 10nA current would be enough for this multiplexer to operate. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. When the digital multiplexer is charged above 500nA, damage can occur. Operating the 2 inputs requires 2 inputs. A 95MHz-bandwidth can be used for data transfer. Drain to Source resistance is 900mOhm. 4 outputs are included in the analogue multiplexer. TS5A23160DGST Features2 Channels Switch Circuit: SPDT 10nA Supply Current Bandwidth: 95MHz Drain-to-Source resistance: 900mOhm TS5A23160DGST ApplicationsThere are a lot of Texas Instruments TS5A23160DGST Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A3159DCKT OverviewShipping overseas is convenient with the electronic component packed in 6-TSSOP, SC-88, SOT-363. High reliability is provided by advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. The operating temperature is extended to around -40°C~85°C TA. 6 terminations have been made so far. Due to its 1 channels, the electrical component produces high-quality output. Turning on and running the electrical part should be easy with a 1.8V voltage supply. A key feature of the 6 series is the inclusion of this electronic part as part of its design. A SPDT switching circuit is used to build these analog multiplexers. Try searching for the analog switch ic with TS5A3159 if you are looking for variants. There is 1.1Ohm internal resistance in this digital multiplexer. The functions of 6 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Analog switch ics with Single supply type are cost-effective. There should be 1.65V voltage fed to the electrical part below 1.65V. The analogue multiplexer could operate on 100nA current. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. Putting voltage greater than 100nA on the multiplexer may cause damage. In order to operate the 1 inputs, there are several steps to follow. A 100MHz-bandwidth can be used for data transfer. This electronic component presents a Drain to Source resistance of 1.5Ohm. An output of 2 is provided by the digital multiplexer. TS5A3159DCKT Features1 Channels Switch Circuit: SPDT 100nA Supply Current Bandwidth: 100MHz Drain-to-Source resistance: 1.5Ohm TS5A3159DCKT ApplicationsThere are a lot of Texas Instruments TS5A3159DCKT Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74AHC4066N OverviewShipping overseas is convenient due to the electrical component's packing in 14-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. 14 terminations have been made so far. A electrical component with 4 channels is capable of high-quality output. If the voltage supply is 2.3V volts, the electrical component should be turned on and run. An injection of 14 pins is performed into the body of the electrical component. These analog multiplexers are built based on SPST - NO switching circuits. 74AHC4066 can be used to search for analog multiplexer variants. There is 75Ohm internal resistance in this digital multiplexer. To find out what the 14 pins do, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Analogue multiplexers of the Single supply type that are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. This analog switch requires a voltage of 2V~5.5V to drain from a single voltage supply. Putting voltage greater than 20μA on the multiplexer may cause damage. There are SEPARATE OUTPUT outputs on this analog switch ic. A 50MHz-bandwidth can be used for data transfer. SN74AHC4066N Features4 Channels Switch Circuit: SPST - NO Bandwidth: 50MHz SN74AHC4066N ApplicationsThere are a lot of Texas Instruments SN74AHC4066N Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4053PW OverviewThis electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 2:1. Operating temperature extended to -55°C~125°C TA. In total, 16 terminations have occurred. Due to its 2 channels, the electrical component produces high-quality output. Turning on and running the electrical part should be easy with a 4.5V voltage supply. Into the electrical component body are injected 16 pins. A SPDT switching circuit is used for these analog switches. This multiplexer is composed of 3 circuits. 74HC4053 can be used to search for analog multiplexer variants. The internal resistance of this digital multiplexer is 130Ohm. Datasheets for 16 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 6V in normal situations. An effective Dual, Single supply digital multiplexer. There should be 2V voltage fed to the electrical part below 2V. Despite this switch device's dual supply capability, its voltage should not exceed 5V. A dual power supply should have at least 1V voltage attached. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. Among the inputs that can be operated are the 6 inputs. 200MHz-bandwidths can be used to transfer data between multiplexers. Drain to Source resistance for this electronic component is 130Ohm. CD74HC4053PW Features2 Channels Switch Circuit: SPDT Bandwidth: 200MHz Drain-to-Source resistance: 130Ohm CD74HC4053PW ApplicationsThere are a lot of Texas Instruments CD74HC4053PW Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4066E OverviewPresented in 14-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. Through Hole is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -55°C~125°C TA. Totally, there are 14 terminations. As a result of its 4 channels, this electronic component provides high-quality output. A 4.5V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 14 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching for 74HC4066 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 70Ohm. Please refer to the datasheets for 14 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 10V. Analogue multiplexers of the Single supply type that are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. A voltage of 2V~10V is required to drain this analog switch from a single voltage supply. Put voltage above 16μA on the multiplexer to cause damage. 200MHz bandwidths enable data to be transferred. CD74HC4066E Features4 Channels Switch Circuit: SPST - NO Bandwidth: 200MHz CD74HC4066E ApplicationsThere are a lot of Texas Instruments CD74HC4066E Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4316M OverviewShipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tube provides high reliability. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -55°C~125°C TA. In total, there are 16 terminations. A electrical component with 4 channels is capable of high-quality output. With a 4.5V voltage supply, the electrical component should be turned on and run. The electrical component body receives 16 pins. Based on SPST - NO switching circuits, these analog multiplexers work. Use 74HC4316 to search for variants of the digital switches. An switch multiplexer with 170Ohm internal resistance has a value of 170Ohm. The functions of 16 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. An effective Dual, Single supply digital multiplexer. 2V is the lowest voltage that should be fed to the electronic electronic part. A voltage higher than 160μA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 5VIf you are using dual power supplies, you should attach at least 1V. 200MHz-bandwidths can be used to transfer data between multiplexers. Check out the electrical component's additional features, such as the following: ALSO OPERATES AT 2V TO 10V (VCC-VEE) SUPPLY. Drain to Source resistance for this electronic component is 170Ohm. CD74HC4316M Features4 Channels Switch Circuit: SPST - NO Bandwidth: 200MHz Additional Features: ALSO OPERATES AT 2V TO 10V (VCC-VEE) SUPPLY Drain-to-Source resistance: 170Ohm CD74HC4316M ApplicationsThere are a lot of Texas Instruments CD74HC4316M Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4066M OverviewShipping overseas is convenient with the electronic component packed in 14-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tube. The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Around -55°C~125°C TA is the extended operating temperature. There are 14 terminations totally. The electronic part delivers high-quality output through its 4 channels. When the electronic component is given a voltage of 4.5V, it should be turned on and run. This electrical component is included in the 14 series of products. The analog switch ics are built using SPST - NO switching circuits. 74HCT4066 can be used to search for analog multiplexer variants. It has an internal resistance of 95Ohm. Datasheets for 14 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Digital switch that provides Single power at a cost-effective price. 4.5V should be the lowest voltage fed to the electronic component. Analogue multiplexers require a 4.5V~5.5V voltage to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 40μA. This electrical part is compatible with 5V operating voltages. It is possible to transfer data over a 200MHz-bandwidth. There is 25Ohm resistance between the Drain and Source on this part. CD74HCT4066M Features4 Channels Switch Circuit: SPST - NO Bandwidth: 200MHz Drain-to-Source resistance: 25Ohm CD74HCT4066M ApplicationsThere are a lot of Texas Instruments CD74HCT4066M Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LV4051AD OverviewThe electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Surface Mount. There is 8:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. Totally, there are 16 terminations. This electronic part offers high-quality output due to its 8 channels. If the voltage supply is 2.3V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. The multiplexer consists of 1 circuits. Search with 74LV4051 if you are looking for analog multiplexer variants. There is 75Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. Analog switch ics with Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 2V. This digital switch can be operated with a current of 20μA. This analog switch requires a voltage of 2V~5.5V to drain from a single voltage supply. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating 8 inputs is required. 35MHz bandwidths enable data to be transferred. SN74LV4051AD Features8 Channels 20μA Supply Current Bandwidth: 35MHz SN74LV4051AD ApplicationsThere are a lot of Texas Instruments SN74LV4051AD Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LV4066APW OverviewDue to its 14-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. 14 terminations have been made so far. By its 4 channels, the electronic component provides high-quality output. When a voltage supply of 2.3V is used, the electronic component should be turned on and run. A total of 14 pins are injected into the electrical part body. Circuits based on SPST - NO switching are used to construct these analog switch ics. Search with 74LV4066 if you are looking for analog multiplexer variants. This digital multiplexer has 75Ohm internal resistance. Please refer to the datasheets for 14 pins functions. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 5.5V. Single supply type digital switch with a low cost. 2V should be the lowest voltage fed to the electronic component. This digital switch can be operated with a current of 20μA. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 20μA. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. 50MHz-bandwidths can be used to transfer data between multiplexers. SN74LV4066APW Features4 Channels Switch Circuit: SPST - NO 20μA Supply Current Bandwidth: 50MHz SN74LV4066APW ApplicationsThere are a lot of Texas Instruments SN74LV4066APW Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote |
Please send RFQ , we will respond immediately.
