Shine Ever will be exhibiting at ELECTRONICA in Munich Nov 12-15, 2024! COME VISIT US AT BOOTH 118/2, Hall C5
My CartGrounding Braid, Straps(2795)
| Image | Part | Manufacturer | Description | Stock | Action | |
|---|---|---|---|---|---|---|
| Texas Instruments | TS5MP645NYFPR OverviewPresented in 36-XFBGA, DSBGA, this electrical component is convenient for overseas shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. 2:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C degrees Celsius. Total terminations are 36. The electronic part delivers high-quality output through its 10 channels. Unlike digital switches, these are based on SPDT switching circuits. 10 circuits are used in this analogue multiplexer. If you are looking for variants of the digital switch, trying search with TS5MP645. To find out what the functions of 36 pins are, please refer to their datasheets. An analogue multiplexer drains from a single voltage supply at 1.65V~5.5V. With a DIFFERENTIAL MULTIPLEXER analog IC integrated into the board. This analog switch ic utilizes SEPARATE OUTPUT output. 1500MHz bandwidths enable data to be transferred. TS5MP645NYFPR Features10 Channels Switch Circuit: SPDT -3db Bandwidth: 1.5GHz Bandwidth: 1500MHz TS5MP645NYFPR ApplicationsThere are a lot of Texas Instruments TS5MP645NYFPR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LVC1G66DCKRG4 OverviewThe electrical component comes in 5-TSSOP, SC-70-5, SOT-353 packaging, which makes it convenient to ship overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. Total terminations are 5. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 1.8V volts, the electrical part can be powered up and run. It is part of the design of the 5 series that this electronic component is included. A SPST - NO switching circuit is used for these analog switches. Use 74LVC1G66 to search for variants of the digital switches. A 10Ohm internal resistance characterizes this multiplexer. You can find the functions of the 5 pins in the datasheets. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. The analog switch ic is of the Single supply type and is cost-effective. 1.65V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 10μA would be sufficient for this switch device. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 10μA. With a SPDT analog IC integrated into the board. In 300MHz-bandwidths, data can be transferred. SN74LVC1G66DCKRG4 Features1 Channels Switch Circuit: SPST - NO 10μA Supply Current -3db Bandwidth: 300MHz Bandwidth: 300MHz SN74LVC1G66DCKRG4 ApplicationsThere are a lot of Texas Instruments SN74LVC1G66DCKRG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LVC1G66DSFR OverviewThe electrical component comes in 6-XFDFN packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. A total of 6 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. An 1.8V voltage supply should allow the electrical part to be turned on and run. A SPST - NO switching circuit is used for these analog switches. Use 74LVC1G66 to search for variants of the digital switches. Analog switches have 10Ohm internal resistance. To find out what the 6 pins do, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Digital switch that provides Single power at a cost-effective price. A low voltage of 1.65V should be applied to the electronic component. The switch device would be able to operate with 10μA current. A voltage of 1.65V~5.5V is required for this switch device, which drains from a single voltage source. A voltage higher than 10μA may cause damage to the switch multiplexer. An analog IC with the number SPDT is integrated into this board. There are various bandwidths available for data transfer. SN74LVC1G66DSFR Features1 Channels Switch Circuit: SPST - NO 10μA Supply Current -3db Bandwidth: 300MHz Bandwidth: 300MHz SN74LVC1G66DSFR ApplicationsThere are a lot of Texas Instruments SN74LVC1G66DSFR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A1066DCKRG4 OverviewShipping overseas is convenient due to the electrical component's packing in 5-TSSOP, SC-70-5, SOT-353. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. In total, 5 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 5 series. The analog switch ics are built using SPST - NO switching circuits. Try searching with TS5A1066 if you're looking for variants. Internally, this switch multiplexer has a resistance of 10Ohm. To find out what the functions of 5 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 1.65V. For this multiplexer to operate, 50nA current would be sufficient. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. As far as the outputs go, this switch multiplexer utilizes COMMON OUTPUT of them. Operating 1 inputs is required. 400MHz bandwidths enable data to be transferred. TS5A1066DCKRG4 Features1 Channels Switch Circuit: SPST - NO 50nA Supply Current Bandwidth: 400MHz TS5A1066DCKRG4 ApplicationsThere are a lot of Texas Instruments TS5A1066DCKRG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | 74LVC1G3157DBVRG4 OverviewThis electronic part is conveniently packaged in SOT-23-6, making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. In total, there are 6 terminations. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 2.3V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 6 pins. Circuits based on SPDT switching are used to construct these analog switch ics. There are 1 circuits in this switch device. Look for analog switch ic variants by searching with 74LVC1G3157. As far as internal resistance is concerned, it has 15Ohm. To find out what the 6 pins do, please refer to the datasheets. There is a standard Multiplexers or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The digital multiplexer has a low cost Single supply. In order for the electronic part to function properly, the lowest voltage should be 1.65V. 1μA current would be enough for this multiplexer to operate. A voltage of 1.65V~5.5V is required for this switch device, which drains from a single voltage source. The analogue multiplexer may be damaged if voltage is greater than 10μA. There are various bandwidths available for data transfer. 2 outputs are included in the analogue multiplexer. 74LVC1G3157DBVRG4 Features1 Channels Switch Circuit: SPDT 1μA Supply Current Bandwidth: 300MHz 74LVC1G3157DBVRG4 ApplicationsThere are a lot of Texas Instruments 74LVC1G3157DBVRG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4051M96G4 OverviewShipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. 8:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -55°C~125°C TA extended. In total, 16 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 4.5V volts, the electrical part can be powered up and run. This electrical component is included in the 16 series of products. A total of 1 circuits make up this switch device. Try searching for 74HCT4051 variants of the analog switch ic. An switch multiplexer with 130Ohm internal resistance has a value of 130Ohm. Datasheets for functions of 16 pins are available. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. An effective Dual, Single supply digital multiplexer. There should be 4.5V voltage fed to the electrical part below 4.5V. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5V. In the case of dual power supplies, you should connect at least 1V. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board. There is a voltage range of 5V operating voltages for the electrical part. A 8 input needs to be operated. There are 180MHz bandwidths for data transfer. CD74HCT4051M96G4 Features1 Channels Bandwidth: 180MHz CD74HCT4051M96G4 ApplicationsThere are a lot of Texas Instruments CD74HCT4051M96G4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4051M96E4 OverviewShipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. There is 8:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -55°C~125°C TA. Total terminations are 16. As a result of its 1 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 4.5V voltage supply. 16 pins are injected to the electronic part body. A 1 circuit is present in this switch device. Try searching with 74HCT4051 to find analog multiplexer variants. In this multiplexer, the internal resistance is 130Ohm. Datasheets for 16 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. 4.5V should be the lowest voltage fed to the electronic component. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 5V. It is recommended that you attach at least 1V to your dual power supply. It is integrated with SINGLE-ENDED MULTIPLEXER analog ICs. This electrical part is compatible with 5V operating voltages. It is possible to operate 8 inputs. The data can be transferred over a wide range of bandwidths, called 180MHz bandwidths. CD74HCT4051M96E4 Features1 Channels Bandwidth: 180MHz CD74HCT4051M96E4 ApplicationsThere are a lot of Texas Instruments CD74HCT4051M96E4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4053M96E4 OverviewShipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -55°C~125°C TA. 16 terminations have been made so far. A electrical component with 3 channels is capable of high-quality output. When the electronic component is given a voltage of 4.5V, it should be turned on and run. This electrical component is included in the 16 series of products. Based on SPDT switching circuits, these analog multiplexers work. Circuits number 3 make up this analogue multiplexer. 74HCT4053 can be used to search for analog multiplexer variants. A 130Ohm internal resistance characterizes this multiplexer. Datasheets for 16 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 5.5V in normal situations. An effective Dual, Single supply digital multiplexer. A low voltage of 4.5V should be applied to the electronic component. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 5V. You should attach at least 1V voltage if you are using dual power supply. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board. It can operate from 5V operating voltages. It is possible to operate 6 inputs. 200MHz bandwidths enable data to be transferred. It is able to conduct in a 2-bit way. CD74HCT4053M96E4 Features3 Channels Switch Circuit: SPDT Bandwidth: 200MHz 2-Bit CD74HCT4053M96E4 ApplicationsThere are a lot of Texas Instruments CD74HCT4053M96E4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LVC1G3157YZTR OverviewPacked in 6-XFBGA, DSBGA, the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. Circuits based on SPDT switching are used to construct these analog switch ics. There are 1 circuits in this switch device. Try searching for the analog switch ic with 74LVC1G3157 if you are looking for variants. As far as internal resistance is concerned, it has 15Ohm. Datasheets for functions of 6 pins are available. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. There should be 1.65V voltage fed to the electrical part below 1.65V. For this multiplexer to operate, 1μA current would be sufficient. This analog switch requires a voltage of 1.65V~5.5V to drain from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 10μA. SN74LVC1G3157YZTR FeaturesSwitch Circuit: SPDT 1μA Supply Current -3db Bandwidth: 340MHz SN74LVC1G3157YZTR ApplicationsThere are a lot of Texas Instruments SN74LVC1G3157YZTR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4053PWRG4 OverviewAs the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 2:1. Increasing operating temperature to around -55°C~125°C TA. Totally, there are 16 terminations. A electrical component with 3 channels is capable of high-quality output. Turning on and running the electrical part should be easy with a 4.5V voltage supply. An injection of 16 pins is performed into the body of the electrical component. These analog multiplexers are built based on SPDT switching circuits. There are 3 circuits in this multiplexer. Look for analog switch ic variants by searching with 74HCT4053. Analog switches have 130Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A cost-effective Dual, Single supply type analogue multiplexer. There should be 4.5V voltage fed to the electrical part below 4.5V. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 5V. A dual power supply should have at least 1V voltage attached. With a SINGLE-ENDED MULTIPLEXER analog IC integrated into the board. Operating voltages range from 5V. The electrical component supports 6 inputs. It is possible to transfer data over a 200MHz-bandwidth. It conducts in a 2-bit manner. CD74HCT4053PWRG4 Features3 Channels Switch Circuit: SPDT Bandwidth: 200MHz 2-Bit CD74HCT4053PWRG4 ApplicationsThere are a lot of Texas Instruments CD74HCT4053PWRG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HCT4052M96G4 OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. 4:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -55°C~125°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 2 channels. When a voltage supply of 4.5V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 16 pins. Unlike digital switches, these are based on SP4T switching circuits. The multiplexer consists of 2 circuits. If you are looking for variants of the digital switch, trying search with 74HCT4052. This digital multiplexer has 130Ohm internal resistance. The functions of 16 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. An effective Dual, Single supply digital multiplexer. There should be 4.5V voltage fed to the electrical part below 4.5V. Despite this switch's dual supply capability, its voltage should not exceed 5V. If you are using dual power supplies, you should attach at least 1V. With a DIFFERENTIAL MULTIPLEXER analog IC integrated into the board. 5V operating voltages can be used with this electrical part. Among the inputs that can be operated are the 8 inputs. 185MHz bandwidths enable data to be transferred. The switch device is capable of conducting in a 4-bit mode. CD74HCT4052M96G4 Features2 Channels Switch Circuit: SP4T Bandwidth: 185MHz 4-Bit CD74HCT4052M96G4 ApplicationsThere are a lot of Texas Instruments CD74HCT4052M96G4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A63157DBVRG4 OverviewPresented in SOT-23-6, this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 6. High-quality output is provided by the electronic component's 1 channels. With a 1.8V voltage supply, the electrical component should be turned on and run. As part of the design of the 6 series, this electronic part has been incorporated into the system. Multiplexers built on a SPDT switching circuit are built. A total of 1 circuits make up this switch device. Look for analog switch ic variants by searching with TS5A63157. It has an internal resistance of 10Ohm. To find out what the functions of 6 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. A cost-effective Single supply type analogue multiplexer. 1.65V should be the lowest voltage fed to the electronic component. For this digital switch to work, 10nA current would suffice. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. Putting voltage greater than 100nA on the multiplexer may cause damage. This analog switch ic utilizes SEPARATE OUTPUT output. Operating the 2 inputs requires 2 inputs. 370MHz-bandwidths can be used to transfer data between multiplexers. TS5A63157DBVRG4 Features1 Channels Switch Circuit: SPDT 10nA Supply Current -3db Bandwidth: 371MHz Bandwidth: 370MHz TS5A63157DBVRG4 ApplicationsThere are a lot of Texas Instruments TS5A63157DBVRG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4053PWRG4 OverviewPresented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -55°C~125°C TA. 16 terminations have been made so far. A 2 channel electronic part produces high-quality output. With a 4.5V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. These analog multiplexers are built based on SPDT switching circuits. The circuits in this analogue multiplexer number 3. Look for analog switch ic variants by searching with 74HC4053. Internally, this switch multiplexer has a resistance of 130Ohm. For functions related to 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 6V volts for the multiplexer. The digital multiplexer has a low cost Dual, Single supply. 2V is the lowest voltage the electrical component should receive. If put voltage greater than 5V on the multiplexer, damage may be caused to the device. The voltage should be at least 1V if you are using dual power supplies. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. Operating 6 inputs is required. It is possible to transfer data over a 200MHz-bandwidth. CD74HC4053PWRG4 Features2 Channels Switch Circuit: SPDT Bandwidth: 200MHz CD74HC4053PWRG4 ApplicationsThere are a lot of Texas Instruments CD74HC4053PWRG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4051M96G4 OverviewDue to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 8:1. Around -55°C~125°C TA is the extended operating temperature. 16 terminations have been made so far. The electronic part delivers high-quality output through its 1 channels. An 4.5V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 16 pins. There are 1 circuits in this switch device. If you are looking for variants of the digital switch, trying search with 74HC4051. Analog switches have 130Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 6V volts for the multiplexer. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage fed to the electronic component should be 2V. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 5V. In the case of dual power supplies, you should connect at least 1V. It is integrated with a SINGLE-ENDED MULTIPLEXER analog IC. The electrical component supports 8 inputs. It is possible to transfer data over a 180MHz-bandwidth. CD74HC4051M96G4 Features1 Channels Bandwidth: 180MHz CD74HC4051M96G4 ApplicationsThere are a lot of Texas Instruments CD74HC4051M96G4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A3166DBVRG4 OverviewPresented in SC-74A, SOT-753, this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. There is 1:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 5. The electronic part delivers high-quality output through its 1 channels. A 1.8V voltage supply should turn on and run the electronic component. There is an electrical component included in the 5 series. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching for the analog switch ic with TS5A3166 if you are looking for variants. It has an internal resistance of 900mOhm. Datasheets for functions of 5 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 5.5V should not normally be supplied to the switches. The digital multiplexer has a low cost Single supply. A low voltage of 1.65V should be applied to the electronic component. The switch device would be able to operate with 10nA current. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 100nA. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating 1 inputs is required. 200MHz-bandwidths can be used to transfer data between multiplexers. TS5A3166DBVRG4 Features1 Channels Switch Circuit: SPST - NO 10nA Supply Current Bandwidth: 200MHz TS5A3166DBVRG4 ApplicationsThere are a lot of Texas Instruments TS5A3166DBVRG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LV4052APWRE4 OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 4:1. Around -40°C~85°C TA is the extended operating temperature. 16 terminations have been made so far. This electronic part offers high-quality output due to its 2 channels. It is safe to turn on and run the electronic component with a 2.5V voltage supply. An electrical component like this is included in the 16 series. Unlike digital switches, these are based on SP4T switching circuits. Circuits number 2 make up this analogue multiplexer. Try searching for 74LV4052 variants of the analog switch ic. An switch multiplexer with 100Ohm internal resistance has a value of 100Ohm. For functions related to 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 2V. It would be sufficient to run this analogue multiplexer with 20μA current. Draining from a single voltage supply, this analog switch requires a voltage of 2V~5.5V. There is an integrated analog IC DIFFERENTIAL MULTIPLEXER in the module. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. There are 8 inputs to be operated. A 50MHz-bandwidth can be used for data transfer. 4-bit operation is possible. SN74LV4052APWRE4 Features2 Channels Switch Circuit: SP4T 20μA Supply Current Bandwidth: 50MHz 4-Bit SN74LV4052APWRE4 ApplicationsThere are a lot of Texas Instruments SN74LV4052APWRE4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4053MG4 OverviewThis electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tube. It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature around -55°C~125°C TA extended. By its 2 channels, the electronic component provides high-quality output. Based on SPDT switching circuits, these analog multiplexers work. A 3 circuit is present in this switch device. If you are looking for variants of the digital switch, trying search with 74HC4053. It has an internal resistance of 130Ohm. To find out what the 16 pins do, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. Dual, Single supply type digital switch with a low cost. 2V is the lowest voltage that should be fed to the electronic electronic part. There is no problem with using dual supply voltage, but it should not exceed 5V. A dual power supply should have at least 1V voltage attached. Operating 6 inputs is required. 200MHz bandwidths enable data to be transferred. During operation, the multiplexer should not be exposed to a temperature above 125°C. 3 outputs are included in the analogue multiplexer. It is possible to purchase a 16-SOIC package from suppliers. CD74HC4053MG4 Features2 Channels Switch Circuit: SPDT -3db Bandwidth: 200MHz Bandwidth: 200MHz CD74HC4053MG4 ApplicationsThere are a lot of Texas Instruments CD74HC4053MG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4051M96E4 OverviewThe electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 8:1. Operational temperature extended around -55°C~125°C TA. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. A 4.5V voltage supply should turn on and run the electronic component. This electronic part can be found in the 16 series. A 1 circuit is present in this switch device. Try searching with 74HC4051 to find analog multiplexer variants. An switch multiplexer with 130Ohm internal resistance has a value of 130Ohm. Datasheets for 16 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 2V is the lowest voltage the electrical component should receive. Despite this switch device's dual supply capability, its voltage should not exceed 5V. For dual power supplies, a voltage of at least 1V should be attached. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. Operating 8 inputs is required. 180MHz bandwidths enable data to be transferred. CD74HC4051M96E4 Features1 Channels Bandwidth: 180MHz CD74HC4051M96E4 ApplicationsThere are a lot of Texas Instruments CD74HC4051M96E4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A2053DCURG4 OverviewPacked in 8-VFSOP (0.091, 2.30mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 8. A electrical component with 1 channels is capable of high-quality output. If the voltage supply is 1.8V volts, the electrical component should be turned on and run. An electrical component like this is included in the 8 series. Unlike digital switches, these are based on SPDT switching circuits. The circuits in this analogue multiplexer number 1. Using the TS5A2053 search parameter, you can discover variants of the switch. There is 13.8Ohm internal resistance in this digital multiplexer. Datasheets for functions of 8 pins are available. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 5.5V voltage to the switch device. A analog switch ic that has a cost-effective Single supply type. There should be 1.65V voltage fed to the electrical part below 1.65V. The switch device would be able to operate with 100nA current. A voltage of 1.65V~5.5V is required for this switch device, which drains from a single voltage source. A digital multiplexer may suffer damage if voltage is applied above 1μA. Operating the 1 inputs requires 1 inputs. A 330MHz-bandwidth can be used for data transfer. 2 outputs are included in the analogue multiplexer. TS5A2053DCURG4 Features1 Channels Switch Circuit: SPDT 100nA Supply Current Bandwidth: 330MHz TS5A2053DCURG4 ApplicationsThere are a lot of Texas Instruments TS5A2053DCURG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74AUC2G53DCURG4 OverviewPresented in 8-VFSOP (0.091, 2.30mm Width), this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 2:1. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 8. By its 2 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 1.1V voltage supply. A total of 8 pins are injected into the electrical part body. Circuits based on SPDT switching are used to construct these analog switch ics. A 1 circuit is present in this switch device. Try searching for the analog switch ic with 74AUC2G53 if you are looking for variants. In this multiplexer, the internal resistance is 15Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 2.7V. Analogue multiplexers of the Single supply type that are cost-effective. 800mV is the lowest voltage the electrical component should receive. This multiplexer would work with 10μA current. A voltage of 0.8V~2.7V is required to drain this analog switch from a single voltage supply. If put voltage greater than 10μA on the device, damage may be caused to the analogue multiplexer. This analog switch ic utilizes SEPARATE OUTPUT output. The electrical component supports 2 inputs. 198MHz bandwidths enable data to be transferred. SN74AUC2G53DCURG4 Features2 Channels Switch Circuit: SPDT 10μA Supply Current -3db Bandwidth: 50MHz Bandwidth: 198MHz SN74AUC2G53DCURG4 ApplicationsThere are a lot of Texas Instruments SN74AUC2G53DCURG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LV4053ADRG4 OverviewShipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a number of circuits 2:1. Operation at a temperature around -40°C~85°C TA. Totally, there are 16 terminations. As a result of its 2 channels, this electronic component provides high-quality output. Powered by a 2.3V voltage supply, the electrical part should be switched on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. A SPDT switching circuit is used for these analog switches. Circuits number 3 make up this analogue multiplexer. Search with 74LV4053 if you are looking for analog multiplexer variants. There is 75Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A analog switch ic that has a cost-effective Single supply type. The lowest voltage fed to the electronic component should be 2V. In order to operate this switch device, it would need a current of 20μA. This analogue multiplexer requires a voltage of 2V~5.5V when it drains from a single voltage supply. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. The 6 inputs need to be operated in order to work. In 50MHz-bandwidths, data can be transferred. SN74LV4053ADRG4 Features2 Channels Switch Circuit: SPDT 20μA Supply Current Bandwidth: 50MHz SN74LV4053ADRG4 ApplicationsThere are a lot of Texas Instruments SN74LV4053ADRG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | TS5A2066DCTRE4 OverviewThe electronic component is convenient to ship overseas because it is packed in a 8-LSSOP, 8-MSOP (0.110, 2.80mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have the same number of circuits 1:1. The operating temperature is extended to around -40°C~85°C TA. In total, 8 terminations have occurred. Due to its 2 channels, the electrical component produces high-quality output. If the voltage supply is 1.8V volts, the electrical component should be turned on and run. Into the electrical component body are injected 8 pins. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with TS5A2066 to find analog multiplexer variants. It has an internal resistance of 10Ohm. For functions related to 8 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Digital switch that provides Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 1.65V. 100nA current would be enough for this multiplexer to operate. This analog switch requires a voltage of 1.65V~5.5V to drain from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. It is possible to operate 2 inputs. It is possible to transfer data over a 300MHz-bandwidth. TS5A2066DCTRE4 Features2 Channels Switch Circuit: SPST - NO 100nA Supply Current Bandwidth: 300MHz TS5A2066DCTRE4 ApplicationsThere are a lot of Texas Instruments TS5A2066DCTRE4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LV4051ADGVRG4 OverviewThe electrical component comes in 16-TFSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. There is 8:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. There are 16 terminations totally. Due to its 8 channels, the electrical component produces high-quality output. In the case of a voltage supply of 2.3V volts, the electrical part can be powered up and run. The electronic part body is injected with 16 pins. A total of 1 circuits make up this switch device. Use 74LV4051 to search for variants of the digital switches. There is 75Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. A cost-effective Single supply type analogue multiplexer. It is recommended to use 2V as the lowest voltage for the electrical part. An operating current of 20μA would be sufficient for this switch device. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. It is possible to operate 8 inputs. A 35MHz-bandwidth can be used for data transfer. SN74LV4051ADGVRG4 Features8 Channels 20μA Supply Current Bandwidth: 35MHz SN74LV4051ADGVRG4 ApplicationsThere are a lot of Texas Instruments SN74LV4051ADGVRG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74LV4052APWE4 OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 4:1. Operational temperature extended around -40°C~85°C TA. In total, there have been 16 terminations. Due to its 2 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 2.5V, it should be turned on and run. A total of 16 pins are injected into the body of the electronic part. On the other hand, analog switches can be constructed using SP4T switching circuits. There are 2 circuits in this switch device. Try searching for the analog switch ic with 74LV4052 if you are looking for variants. It has an internal resistance of 100Ohm. The datasheets for the 16 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 20μA current would be sufficient. Analogue multiplexers require a 2V~5.5V voltage to drain from a single voltage supply. It is integrated with DIFFERENTIAL MULTIPLEXER analog ICs. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. There are 8 inputs to be operated. This switch operates within the bandwidth of 50MHz. The switch device is capable of conducting in a 4-bit mode. SN74LV4052APWE4 Features2 Channels Switch Circuit: SP4T 20μA Supply Current Bandwidth: 50MHz 4-Bit SN74LV4052APWE4 ApplicationsThere are a lot of Texas Instruments SN74LV4052APWE4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4053EG4 OverviewThis electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tube is used. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature around -55°C~125°C TA extended. SPDT switching circuits are used in these analog switch ics. It consists of 3 circuits. Try searching for the analog switch ic with 74HC4053 if you are looking for variants. CD74HC4053EG4 FeaturesSwitch Circuit: SPDT -3db Bandwidth: 200MHz CD74HC4053EG4 ApplicationsThere are a lot of Texas Instruments CD74HC4053EG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD4097BME4 OverviewShipping overseas is convenient due to the electrical component's packing in 24-SOIC (0.295, 7.50mm Width). Advanced packaging method Tube is used to provide high reliability. The multiplexer is located in Surface Mount. 8:1 is the ratio of multiplexer to demultiplexer circuits. Temperatures around -55°C~125°C TA are extended for operation. A total of 24 terminations have been recorded. This electronic part offers high-quality output due to its 2 channels. A 5V voltage supply should turn on and run the electronic component. As part of its design, the 24 series is equipped with this electronic component. The circuits in this analogue multiplexer number 2. Try searching with CD4097 to find analog multiplexer variants. Analog switches have 240Ohm internal resistance. For details about the functions of 24 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 18V. Single supply type digital switch with a low cost. There should be 3V voltage fed to the electrical part below 3V. An operating current of 80nA would be sufficient for this switch device. Using a single voltage supply, this switch device consumes 3V~18V volts. It is integrated with DIFFERENTIAL MULTIPLEXER analog ICs. There are 20MHz bandwidths for data transfer. It conducts in a 8-bit manner. CD4097BME4 Features2 Channels 80nA Supply Current Bandwidth: 20MHz 8-Bit CD4097BME4 ApplicationsThere are a lot of Texas Instruments CD4097BME4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | SN74AHC4066NG4 OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 14-DIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. Mounted in Through Hole is this multiplexer. There is 1:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. Based on SPST - NO switching circuits, these analog multiplexers work. The multiplexer consists of 4 circuits. If you are looking for variants of the digital switch, trying search with 74AHC4066. Using only a single voltage supply, this analog switch requires 2V~5.5V voltage. SN74AHC4066NG4 FeaturesSwitch Circuit: SPST - NO -3db Bandwidth: 50MHz SN74AHC4066NG4 ApplicationsThere are a lot of Texas Instruments SN74AHC4066NG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD74HC4066PWG4 OverviewShipping overseas is convenient with the electronic component packed in 14-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operational temperature extended around -55°C~125°C TA. There are 14 terminations totally. High-quality output is provided by the electronic component's 4 channels. An 4.5V voltage supply should allow the electrical part to be turned on and run. A total of 14 pins are injected into the body of the electronic part. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Using the 74HC4066 search parameter, you can discover variants of the switch. A 70Ohm internal resistance characterizes this multiplexer. You can find the functions of the 14 pins in the datasheets. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 10V in normal situations. Single supply type digital switch with a low cost. 2V should be the lowest voltage fed to the electronic component. A voltage of 2V~10V is required for this switch device, which drains from a single voltage source. A digital multiplexer may suffer damage if voltage is applied above 16μA. In 200MHz-bandwidths, data can be transferred. CD74HC4066PWG4 Features4 Channels Switch Circuit: SPST - NO Bandwidth: 200MHz CD74HC4066PWG4 ApplicationsThere are a lot of Texas Instruments CD74HC4066PWG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| Texas Instruments | CD4052BMG4 OverviewThis electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. Advanced packaging method Tube is used to provide high reliability. This analog switch is mounted in Surface Mount. 4:1 is the number of circuits in the multiplexer and demultiplexer. Around -55°C~125°C TA is the extended operating temperature. A electrical component with 2 channels is capable of high-quality output. Circuits based on SP4T switching are used to construct these analog switch ics. There are 2 circuits in this multiplexer. Try searching for CD4052 variants of the analog switch ic. This digital multiplexer has 240Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. In normalcircumstances, users should not exceed 20V volts for the multiplexer. Digital switch that provides Dual, Single power at a cost-effective price. 3V is the lowest voltage that should be fed to the electronic electronic part. 80nA current would be enough for this multiplexer to operate. Despite this switch's dual supply capability, its voltage should not exceed 9V. If you are using dual power supplies, you should attach at least 2.5V. 18V operating voltages are supported by the electronic component. Operating 8 inputs is required. In 25MHz-bandwidths, data can be transferred. In an environment with a temperature higher than 125°C, the digital switches should not operate. In this digital multiplexer, there are 2 outputs. Suppliers are offering a 16-SOIC package. It is able to conduct in a 4-bit way. CD4052BMG4 Features2 Channels Switch Circuit: SP4T 80nA Supply Current -3db Bandwidth: 25MHz Bandwidth: 25MHz 4-Bit CD4052BMG4 ApplicationsThere are a lot of Texas Instruments CD4052BMG4 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
| STMicroelectronics | STG4158BJR OverviewShipping overseas is convenient due to the electrical component's packing in 6-WFBGA, FCBGA. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 2:1. The operating temperature is extended to around -40°C~85°C TA. There are 6 terminations totally. A electrical component with 1 channels is capable of high-quality output. If the voltage supply is 1.8V volts, the electrical component should be turned on and run. Into the electrical component body are injected 6 pins. A SPDT switching circuit is used to build these analog multiplexers. The multiplexer consists of 1 circuits. Try searching with STG4158 if you're looking for variants. Analog switches have 2Ohm internal resistance. To find out what the 6 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 4.5V. Single supply type digital switch with a low cost. There should be 1.65V voltage fed to the electrical part below 1.65V. 9μA current would be enough for this multiplexer to operate. Analogue multiplexers require a 1.65V~4.5V voltage to drain from a single voltage supply. STG4158BJR Features1 Channels Switch Circuit: SPDT 9μA Supply Current -3db Bandwidth: 40MHz STG4158BJR ApplicationsThere are a lot of STMicroelectronics STG4158BJR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote |
Please send RFQ , we will respond immediately.
