Image | Part | Manufacturer | Description | Stock | Action | |
---|---|---|---|---|---|---|
Texas Instruments | CD4053BPW OverviewPacked in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Extended operating temperature around -55°C~125°C TA. 16 terminations have been made so far. A 2 channel electronic part produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. Into the electrical component body are injected 16 pins. Based on SPDT switching circuits, these analog multiplexers work. There are 3 circuits in this multiplexer. Use CD4053 to search for variants of the digital switches. Analog switches have 240Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. normally, users should not supply switches with voltages higher than 20V. An effective Dual, Single supply digital multiplexer. A low voltage of 3V should be applied to the electronic component. The switch device would be able to operate with 80nA current. Despite this switch's dual supply capability, its voltage should not exceed 9V. If you are using a dual power supply, you should attach at least 2.5V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Operating voltages of 18V are compatible with the electrical part. It is possible to operate 6 inputs. A 30MHz-bandwidth can be used for data transfer. The Drain to Source resistance of this electronic component is 125Ohm. CD4053BPW Features2 Channels Switch Circuit: SPDT 80nA Supply Current Bandwidth: 30MHz Drain-to-Source resistance: 125Ohm CD4053BPW ApplicationsThere are a lot of Texas Instruments CD4053BPW Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | SN74LV4066AD OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 14-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature around -40°C~85°C TA extended. 14 terminations have been made so far. The electronic part provides high-quality output because it has 4 channels. If the voltage supply is 2.3V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 14 pins. The analog switch ics are built using SPST - NO switching circuits. Look for analog switch ic variants by searching with 74LV4066. Analog switches have 75Ohm internal resistance. Please refer to the datasheets for 14 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 2V. The switch device would be able to operate with 20μA current. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. A digital multiplexer may suffer damage if voltage is applied above 20μA. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. This switch operates within the bandwidth of 50MHz. SN74LV4066AD Features4 Channels Switch Circuit: SPST - NO 20μA Supply Current Bandwidth: 50MHz SN74LV4066AD ApplicationsThere are a lot of Texas Instruments SN74LV4066AD Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | SN74LV4053APWT OverviewAs the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature around -40°C~85°C TA extended. In total, there are 16 terminations. A high-quality output is provided by the electrical component's 2 channels. When the electronic component is given a voltage of 2.3V, it should be turned on and run. 16 pins are injected to the electronic part body. Multiplexers built on a SPDT switching circuit are built. There are 3 circuits in this switch device. 74LV4053 can be used to search for analog multiplexer variants. An switch multiplexer with 180Ohm internal resistance has a value of 180Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Multiplexers should not be powered above 5.5V in normal situations. An effective Single supply digital multiplexer. 2V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 20μA current. Using a single voltage supply, this switch device consumes 2V~5.5V volts. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. Operating the 6 inputs requires 6 inputs. This switch operates within the bandwidth of 50MHz. SN74LV4053APWT Features2 Channels Switch Circuit: SPDT 20μA Supply Current Bandwidth: 50MHz SN74LV4053APWT ApplicationsThere are a lot of Texas Instruments SN74LV4053APWT Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | CD74HC4051MT OverviewShipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 8:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -55°C~125°C TA extended. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 1 channels. With a 4.5V voltage supply, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. The circuits in this analogue multiplexer number 1. Look for analog switch ic variants by searching with 74HC4051. In this multiplexer, the internal resistance is 130Ohm. You can find the functions of the 16 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 6V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. Despite this switch's dual supply capability, its voltage should not exceed 5V. If you are using dual power supplies, you should attach at least 1V. It is integrated with SINGLE-ENDED MULTIPLEXER analog ICs. A 8 input needs to be operated. This switch operates within the bandwidth of 180MHz. CD74HC4051MT Features1 Channels Bandwidth: 180MHz CD74HC4051MT ApplicationsThere are a lot of Texas Instruments CD74HC4051MT Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | CD74HC4066MT OverviewPresented in 14-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -55°C~125°C TA extended. In total, there are 14 terminations. A high-quality output is provided by the electrical component's 4 channels. If the voltage supply is 4.5V volts, the electrical component should be turned on and run. A key feature of the 14 series is the inclusion of this electronic part as part of its design. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching for the analog switch ic with 74HC4066 if you are looking for variants. In this multiplexer, the internal resistance is 70Ohm. For details about the functions of 14 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 10V voltage to the switch device. The digital multiplexer has a low cost Single supply. 2V is the lowest voltage that should be fed to the electronic electronic part. The voltage required by this switch device is 2V~10V, draining from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 16μA. It is possible to transfer data over a 200MHz-bandwidth. CD74HC4066MT Features4 Channels Switch Circuit: SPST - NO Bandwidth: 200MHz CD74HC4066MT ApplicationsThere are a lot of Texas Instruments CD74HC4066MT Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | HD3SS3411IRWAT OverviewDue to its 14-WFQFN Exposed Pad packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operation at a temperature around -40°C~105°C TA. In total, there have been 14 terminations. High-quality output is provided by the electronic component's 1 channels. Powered by a 3.3V voltage supply, the electrical part should be switched on and run. A total of 1 circuits make up this switch device. HD3SS3411 can be used to search for analog multiplexer variants. For functions related to 14 pins, please refer to the datasheets. This analog switch requires a voltage of 3V~3.6V to drain from a single voltage supply. It is integrated with DIFFERENTIAL MULTIPLEXER analog ICs. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. A 7.5 GHz-bandwidth can be used for data transfer. HD3SS3411IRWAT Features1 Channels Bandwidth: 7.5 GHz HD3SS3411IRWAT ApplicationsThere are a lot of Texas Instruments HD3SS3411IRWAT Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | TS3A5018D OverviewDue to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tube. In Surface Mount, you'll find this switch device. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. This electronic part offers high-quality output due to its 4 channels. An 2.5V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 16 pins. These analog multiplexers are built based on SPDT switching circuits. Try searching for TS3A5018 variants of the analog switch ic. This digital multiplexer has 10Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 3.6V. A analog switch ic that has a cost-effective Single supply type. 2.3V should be the lowest voltage fed to the electronic component. For this digital switch to work, 2.5μA current would suffice. An analogue multiplexer drains from a single voltage supply at 1.65V~3.6V. The switch multiplexer may be damaged if it is exposed to voltage greater than 7μA. 3V operating voltages can be used with this electrical part. Among the inputs that can be operated are the 4 inputs. There are various bandwidths available for data transfer. The analog switch ics has 8 outputs. TS3A5018D Features4 Channels Switch Circuit: SPDT 2.5μA Supply Current Bandwidth: 300MHz TS3A5018D ApplicationsThere are a lot of Texas Instruments TS3A5018D Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | CD74HC4066PWT OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 14-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around -55°C~125°C TA. In total, there are 14 terminations. Due to its 4 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 4.5V, it should be turned on and run. As part of the design of the 14 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching for 74HC4066 variants of the analog switch ic. A 70Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 14 pins functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 10V to a switch device. The analog switch ic is of the Single supply type and is cost-effective. 2V is the lowest voltage the electrical component should receive. A voltage of 2V~10V is required for this switch device, which drains from a single voltage source. If you put voltage higher than 16μA on the digital multiplexer, damage may occur. There are 200MHz bandwidths for data transfer. CD74HC4066PWT Features4 Channels Switch Circuit: SPST - NO Bandwidth: 200MHz CD74HC4066PWT ApplicationsThere are a lot of Texas Instruments CD74HC4066PWT Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | CD74HC4053MT OverviewAs the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. An extended operating temperature of -55°C~125°C TA degrees Celsius. 16 terminations have been made so far. This electronic part offers high-quality output due to its 2 channels. When a voltage supply of 4.5V is used, the electronic component should be turned on and run. This electrical component is included in the 16 series of products. A SPDT switching circuit is used for these analog switches. This multiplexer is composed of 3 circuits. Try searching with 74HC4053 if you're looking for variants. As far as internal resistance is concerned, it has 180Ohm. Datasheets for functions of 16 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. A low voltage of 2V should be applied to the electronic component. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 5V. A dual power supply should have at least 1V voltage attached. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. Operating the 6 inputs requires 6 inputs. In 200MHz-bandwidths, data can be transferred. CD74HC4053MT Features2 Channels Switch Circuit: SPDT Bandwidth: 200MHz CD74HC4053MT ApplicationsThere are a lot of Texas Instruments CD74HC4053MT Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | SN74LVC1G66QDCKRQ1 OverviewThe electronic component is convenient to ship overseas because it is packed in a 5-TSSOP, SC-70-5, SOT-353. The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around -40°C~125°C TA. In total, there have been 5 terminations. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 2.3V voltage supply. As part of its design, the 5 series is equipped with this electronic component. SPST - NO switching circuits are used in these analog switch ics. Look for analog switch ic variants by searching with 74LVC1G66. This digital multiplexer has 10Ohm internal resistance. For details about the functions of 5 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 1.65V. For this multiplexer to operate, 10μA current would be sufficient. Using a single voltage supply, this switch device consumes 1.65V~5.5V volts. If you put voltage higher than 10μA on the digital multiplexer, damage may occur. In this switch multiplexer, there are COMMON OUTPUT outputs available. In 195MHz-bandwidths, data can be transferred. The series starts with Automotive, AEC-Q100. SN74LVC1G66QDCKRQ1 Features1 Channels Switch Circuit: SPST - NO 10μA Supply Current -3db Bandwidth: 300MHz Bandwidth: 195MHz SN74LVC1G66QDCKRQ1 ApplicationsThere are a lot of Texas Instruments SN74LVC1G66QDCKRQ1 Analog Switches & Multiplexers ICs applications.
|
8254
In-stock
|
Get Quote | |||
Texas Instruments | SN74AUC2G53DCUR OverviewThe electrical component comes in 8-VFSOP (0.091, 2.30mm Width) packaging, which makes it convenient to ship overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 8. The electronic part provides high-quality output because it has 2 channels. Turning on and running the electrical part should be easy with a 1.1V voltage supply. This electronic part can be found in the 8 series. A SPDT switching circuit is used for these analog switches. 1 circuits are used in this analogue multiplexer. 74AUC2G53 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 15Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 2.7V volts for the multiplexer. The digital multiplexer has a low cost Single supply. 800mV is the lowest voltage that should be fed to the electronic electronic part. 10μA current would be enough for this multiplexer to operate. This analogue multiplexer requires a voltage of 0.8V~2.7V when it drains from a single voltage supply. A voltage higher than 10μA may cause damage to the switch multiplexer. It is possible to operate 2 inputs. The transfer of data can be performed over 198MHz bandwidths. SN74AUC2G53DCUR Features2 Channels Switch Circuit: SPDT 10μA Supply Current -3db Bandwidth: 50MHz Bandwidth: 198MHz SN74AUC2G53DCUR ApplicationsThere are a lot of Texas Instruments SN74AUC2G53DCUR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
STMicroelectronics | M74HC4852YRM13TR OverviewAs the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 4:1. Temperatures around -40°C~125°C TA are extended for operation. This electronic part offers high-quality output due to its 4 channels. Circuits based on SP4T switching are used to construct these analog switch ics. There are 2 circuits in this multiplexer. Try searching with M74HC48 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 650Ohm. To find out what the 16 pins do, please refer to the datasheets. A voltage higher than 6V should not normally be supplied to the switches. The digital multiplexer has a low cost Single supply. It is recommended that the electrical component receives a voltage of 2V. For this digital switch to work, 2μA current would suffice. This analog switch requires a voltage of 2V~6V to drain from a single voltage supply. It is integrated with DIFFERENTIAL MULTIPLEXER analog ICs. The Automotive, AEC-Q100 series includes it. M74HC4852YRM13TR Features4 Channels Switch Circuit: SP4T 2μA Supply Current M74HC4852YRM13TR ApplicationsThere are a lot of STMicroelectronics M74HC4852YRM13TR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
NXP Semiconductors | NX3L1T384GM,115 OverviewShipping overseas is convenient with the electronic component packed in 6-XFDFN. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~125°C TA. Total terminations are 6. Electronic part bodies are injected with 6 pins. The analog switch ics are built using SPST - NC switching circuits. A total of 1 circuits make up this switch device. Try searching with NX3L1T384G if you're looking for variants. In this analog multiplexer, the value is Multiplexer or Switches. This analogue multiplexer requires a voltage of 1.4V~4.3V when it drains from a single voltage supply. NX3L1T384GM,115 FeaturesSwitch Circuit: SPST - NC -3db Bandwidth: 60MHz NX3L1T384GM,115 ApplicationsThere are a lot of NXP USA Inc. NX3L1T384GM,115 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | CLV4053ATPWRG4Q1 OverviewDue to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~105°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 3 channels. When a voltage supply of 2.3V is used, the electronic component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Circuits based on SPDT switching are used to construct these analog switch ics. There are 3 circuits in this multiplexer. Look for analog switch ic variants by searching with 74LV4053. Internally, this switch multiplexer has a resistance of 75Ohm. For details about the functions of 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. For this digital switch to work, 20μA current would suffice. This analogue multiplexer requires a voltage of 2V~5.5V when it drains from a single voltage supply. 50MHz bandwidths enable data to be transferred. It is capable of carrying out 2-bit operation. It comes from the Automotive, AEC-Q100 series. CLV4053ATPWRG4Q1 Features3 Channels Switch Circuit: SPDT 20μA Supply Current Bandwidth: 50MHz 2-Bit CLV4053ATPWRG4Q1 ApplicationsThere are a lot of Texas Instruments CLV4053ATPWRG4Q1 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | CD74HCT4051QM96Q1 OverviewShipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. There is 8:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~125°C TA degrees Celsius. In total, 16 terminations have occurred. The electronic part delivers high-quality output through its 8 channels. It is safe to turn on and run the electronic component with a 4.5V voltage supply. It is injected into the electrical part body with 16 pins. A total of 1 circuits make up this switch device. Try searching with 74HCT4051 if you're looking for variants. There is 130Ohm internal resistance in this digital multiplexer. The datasheets for the 16 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 4.5V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 8μA would be sufficient for this switch device. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 5.5V. A dual power supply should have at least 1V voltage attached. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. Operating voltages range from 5V. In order to operate the 8 inputs, there are several steps to follow. The transfer of data can be performed over 180MHz bandwidths. It comes from the Automotive, AEC-Q100 series. CD74HCT4051QM96Q1 Features8 Channels 8μA Supply Current Bandwidth: 180MHz CD74HCT4051QM96Q1 ApplicationsThere are a lot of Texas Instruments CD74HCT4051QM96Q1 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | SN74LV4051ADGVR OverviewPresented in 16-TFSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have the same number of circuits 8:1. Operation at a temperature around -40°C~85°C TA. Totally, there are 16 terminations. High-quality output is provided by the electronic component's 8 channels. It is safe to turn on and run the electronic component with a 2.3V voltage supply. As part of its design, the 16 series is equipped with this electronic component. Circuits number 1 make up this analogue multiplexer. Try searching with 74LV4051 to find analog multiplexer variants. An switch multiplexer with 75Ohm internal resistance has a value of 75Ohm. The functions of 16 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. The digital multiplexer has a low cost Single supply. 2V is the lowest voltage that should be fed to the electronic electronic part. 20μA current would be enough for this multiplexer to operate. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. There are SEPARATE OUTPUT outputs on this analog switch ic. A 8 input needs to be operated. The transfer of data can be performed over 35MHz bandwidths. SN74LV4051ADGVR Features8 Channels 20μA Supply Current Bandwidth: 35MHz SN74LV4051ADGVR ApplicationsThere are a lot of Texas Instruments SN74LV4051ADGVR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | <h3>CD74HC4051NSR Overview</h3><div><br/>Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.209, 5.30mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 8:1. Operation at a temperature around -55°C~125°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 1 channels. Powered by a 4.5V voltage supply, the electrical part should be switched on and run. An injection of 16 pins is performed into the body of the electrical component. There are 1 circuits in this switch device. Search with 74HC4051 if you are looking for analog multiplexer variants. There is 130Ohm internal resistance in this digital multiplexer. Datasheets for 16 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. Despite this switch device's dual supply capability, its voltage should not exceed 5V. If you are using a dual power supply, you should attach at least 1V. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. Operating 8 inputs is required. It is possible to transfer data over a 180MHz-bandwidth. <br/><br/></div><h3>CD74HC4051NSR Features</h3><div><br/>1 Channels<br/>Bandwidth: 180MHz<br/><br/></div><h3>CD74HC4051NSR Applications</h3><div><br/>There are a lot of Texas Instruments CD74HC4051NSR Analog Switches & Multiplexers ICs applications. <br/><br/></div><ul style="padding: 0px; margin: 0px;"><li>Private Branch Exchange (PBX)<!--<li--></li><li>Battery Powered Instruments<!--<li--></li><li>Precision data acquisition<!--<li--></li><li>Digital access cross connects<!--<li--></li><li>Public switching systems<!--<li--></li><li>Switching Systems<!--<li--></li><li>Frame Relay Equipment<!--<li--></li><li>PCMCIA cards<!--<li--></li><li>Fiber to the Home<!--<li--></li><li>Medical<!--<li--></li></ul> |
999
In-stock
|
Get Quote | |||
Texas Instruments | TS5A1066YZPR OverviewPresented in 5-XFBGA, DSBGA, this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. In total, 5 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 1.8V voltage supply. It is injected into the electrical part body with 5 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching for the analog switch ic with TS5A1066 if you are looking for variants. Internally, this switch multiplexer has a resistance of 10Ohm. For details about the functions of 5 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 1.65V. The switch device would be able to operate with 50nA current. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA. It is possible to transfer data over a 400MHz-bandwidth. TS5A1066YZPR Features1 Channels Switch Circuit: SPST - NO 50nA Supply Current Bandwidth: 400MHz TS5A1066YZPR ApplicationsThere are a lot of Texas Instruments TS5A1066YZPR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
NXP Semiconductors | NX3L2T66GM,125 OverviewPacked in 8-XFQFN Exposed Pad, the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Extended operating temperature around -40°C~125°C TA. It is part of the design of the 8 series that this electronic component is included. These analog multiplexers are built based on SPST - NO switching circuits. The multiplexer consists of 2 circuits. Use NX3L2T66G to search for variants of the digital switches. Using a single voltage supply, this switch device consumes 1.4V~4.3V volts. NX3L2T66GM,125 FeaturesSwitch Circuit: SPST - NO -3db Bandwidth: 60MHz NX3L2T66GM,125 ApplicationsThere are a lot of NXP USA Inc. NX3L2T66GM,125 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | SN74LV4053AN OverviewThe electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. Mounted in Through Hole is this multiplexer. Multiplexers and demultiplexers have the same number of circuits 2:1. Operating temperature extended to -40°C~85°C TA. There are 16 terminations totally. As a result of its 2 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 2.3V, it should be turned on and run. 16 pins are injected to the electronic part body. The analog switch ics are built using SPDT switching circuits. This multiplexer is composed of 3 circuits. Try searching for 74LV4053 variants of the analog switch ic. A 75Ohm internal resistance characterizes this multiplexer. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A cost-effective Single supply type analogue multiplexer. 2V should be the lowest voltage fed to the electronic component. The analogue multiplexer could operate on 20μA current. Draining from a single voltage supply, this analog switch requires a voltage of 2V~5.5V. There are SEPARATE OUTPUT outputs on this analog switch ic. The electrical component supports 6 inputs. 50MHz-bandwidths can be used to transfer data between multiplexers. SN74LV4053AN Features2 Channels Switch Circuit: SPDT 20μA Supply Current Bandwidth: 50MHz SN74LV4053AN ApplicationsThere are a lot of Texas Instruments SN74LV4053AN Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | SN74AUC2G66DCTR OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 8-LSSOP, 8-MSOP (0.110, 2.80mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, 8 terminations have occurred. A high-quality output is provided by the electrical component's 2 channels. Turning on and running the electrical part should be easy with a 1.1V voltage supply. 8 pins are injected to the electronic part body. Based on SPST - NO switching circuits, these analog multiplexers work. Use 74AUC2G66 to search for variants of the digital switches. Analog switches have 15Ohm internal resistance. The datasheets for the 8 pins explain the functions. There is a standard Multiplexer or Switches analogue multiplexer here. Users shouldn't supply more than 2.7V voltage to the switch device. A analog switch ic that has a cost-effective Single supply type. 800mV is the lowest voltage the electrical component should receive. The switch device would be able to operate with 10μA current. This analogue multiplexer requires a voltage of 0.8V~2.7V when it drains from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 10μA. The data can be transferred over a wide range of bandwidths, called 500MHz bandwidths. SN74AUC2G66DCTR Features2 Channels Switch Circuit: SPST - NO 10μA Supply Current -3db Bandwidth: 50MHz Bandwidth: 500MHz SN74AUC2G66DCTR ApplicationsThere are a lot of Texas Instruments SN74AUC2G66DCTR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | CD4051BNSR OverviewAs the electronic part is packed in 16-SOIC (0.209, 5.30mm Width), international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Cut Tape (CT). Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 8:1. Increasing operating temperature to around -55°C~125°C TA. Totally, there are 16 terminations. As a result of its 8 channels, this electronic component provides high-quality output. A 5V voltage supply should turn on and run the electronic component. An injection of 16 pins is performed into the body of the electrical component. The multiplexer consists of 1 circuits. Try searching with CD4051 if you're looking for variants. Internally, this switch multiplexer has a resistance of 240Ohm. The datasheets for the 16 pins explain the functions. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 20V to a switch device. The digital multiplexer has a low cost Dual, Single supply. It is recommended to use 3V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 80nA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 9V. It is recommended that you attach at least 2.5V to your dual power supply. This product is integrated with an analog integrated circuit (IC) of type SINGLE-ENDED MULTIPLEXER. This analog switch ic utilizes SEPARATE OUTPUT output. Operating voltages range from 18V. Among the inputs that can be operated are the 8 inputs. There are 20MHz bandwidths for data transfer. CD4051BNSR Features8 Channels 80nA Supply Current Bandwidth: 20MHz CD4051BNSR ApplicationsThere are a lot of Texas Instruments CD4051BNSR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | TS5A3154YZPR OverviewThe electronic part can be shipped overseas conveniently because it is packaged in 8-XFBGA, DSBGA. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 8. A 1 channel electronic part produces high-quality output. When a voltage supply of 1.8V is used, the electronic component should be turned on and run. A total of 8 pins are injected into the electrical part body. On the other hand, analog switches can be constructed using SPDT switching circuits. There are 1 circuits in this switch device. Try searching for the analog switch ic with TS5A3154 if you are looking for variants. An switch multiplexer with 900mOhm internal resistance has a value of 900mOhm. Datasheets for 8 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. It is recommended that the electrical component receives a voltage of 1.65V. The analogue multiplexer could operate on 20nA current. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. The switch multiplexer may be damaged if it is exposed to voltage greater than 100nA. There are various bandwidths available for data transfer. There are 2 outputs on the analogue multiplexer. TS5A3154YZPR Features1 Channels Switch Circuit: SPDT 20nA Supply Current Bandwidth: 100MHz TS5A3154YZPR ApplicationsThere are a lot of Texas Instruments TS5A3154YZPR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | CD4051BQPWRQ1 OverviewPacked in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. There is 8:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~125°C TA. 16 terminations have been made so far. High-quality output is provided by the electronic component's 8 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. There are 16 pins injected into the electronic part body. This multiplexer is composed of 1 circuits. Using the CD4051 search parameter, you can discover variants of the switch. There is 240Ohm internal resistance in this digital multiplexer. You can find the functions of the 16 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 20V voltage to the switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. A low voltage of 5V should be applied to the electronic component. The switch device would be able to operate with 80nA current. For this switch, a dual supply voltage is feasible, but it must not exceed 10VWhen using dual power supplies, you should attach at least 2.5V. Integrated with SINGLE-ENDED MULTIPLEXER analog IC. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Operating 8 inputs is required. The transfer of data can be performed over 20MHz bandwidths. It belongs to the series Automotive, AEC-Q100. CD4051BQPWRQ1 Features8 Channels 80nA Supply Current Bandwidth: 20MHz CD4051BQPWRQ1 ApplicationsThere are a lot of Texas Instruments CD4051BQPWRQ1 Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | TMUX1204DGSR OverviewThis electronic part is conveniently packaged in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. 4:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~125°C TA. Total terminations are 10. A high-quality output is provided by the electrical component's 2 channels. With a 5V voltage supply, the electrical component should be turned on and run. A SP4T switching circuit is used for these analog switches. It consists of 1 circuits. Try searching with TMUX1204 to find analog multiplexer variants. This analog switch requires a voltage of 1.08V~5.5V to drain from a single voltage supply. It is integrated with SINGLE-ENDED MULTIPLEXER analog ICs. This switch operates within the bandwidth of 125MHz. TMUX1204DGSR Features2 Channels Switch Circuit: SP4T -3db Bandwidth: 125MHz Bandwidth: 125MHz TMUX1204DGSR ApplicationsThere are a lot of Texas Instruments TMUX1204DGSR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | CD74HCT4316E OverviewThis electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tube is used. It is mounted in the position Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -55°C~125°C TA. Total terminations are 16. As a result of its 4 channels, this electronic component provides high-quality output. If the voltage supply is 4.5V volts, the electrical component should be turned on and run. This electrical component is included in the 16 series of products. Unlike digital switches, these are based on SPST - NO switching circuits. Search with 74HCT4316 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 170Ohm. The functions of 16 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 4.5V. If put voltage greater than 16μA on the device, damage may be caused to the analogue multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 5V. For dual power supplies, a voltage of at least 1V should be attached. Operating voltages range from 5V. There are 200MHz bandwidths for data transfer. Don't forget the additional features of this electronic part, such as: ALSO OPERATES AT 2V TO 10V (VCC-VEE) SUPPLY. CD74HCT4316E Features4 Channels Switch Circuit: SPST - NO Bandwidth: 200MHz Additional Features: ALSO OPERATES AT 2V TO 10V (VCC-VEE) SUPPLY CD74HCT4316E ApplicationsThere are a lot of Texas Instruments CD74HCT4316E Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | SN74LV4052AN OverviewThis electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. To ensure high reliability, a new packaging method Tube is used. This analog switch is mounted in Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 4:1. Extended operating temperature around -40°C~85°C TA. The total number of terminations is 16. A high-quality output is provided by the electrical component's 2 channels. If the voltage supply is 2.5V volts, the electrical component should be turned on and run. An electrical component like this is included in the 16 series. Based on SP4T switching circuits, these analog multiplexers work. A 2 circuit is present in this switch device. Search with 74LV4052 if you are looking for analog multiplexer variants. It has an internal resistance of 100Ohm. Datasheets for 16 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 2V. This multiplexer would work with 20μA current. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. A 8 input needs to be operated. 50MHz bandwidths enable data to be transferred. It can conduct 4-bit signals. SN74LV4052AN Features2 Channels Switch Circuit: SP4T 20μA Supply Current Bandwidth: 50MHz 4-Bit SN74LV4052AN ApplicationsThere are a lot of Texas Instruments SN74LV4052AN Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | MAX4597DBVR OverviewShipping overseas is convenient due to the electrical component's packing in SC-74A, SOT-753. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. Total terminations are 5. A high-quality output is provided by the electrical component's 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. A key feature of the 5 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPST - NC switching circuits. If you are looking for variants of the digital switch, trying search with MAX4597. A 10Ohm internal resistance characterizes this multiplexer. Datasheets for 5 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 2V as the lowest voltage for the electrical part. An operating current of 1μA would be sufficient for this switch device. An analogue multiplexer drains from a single voltage supply at 2.4V~5.5V. A voltage higher than 1μA may cause damage to the switch multiplexer. 300MHz bandwidths enable data to be transferred. MAX4597DBVR Features1 Channels Switch Circuit: SPST - NC 1μA Supply Current Bandwidth: 300MHz MAX4597DBVR ApplicationsThere are a lot of Texas Instruments MAX4597DBVR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
STMicroelectronics | M74HCT4051RM13TR OverviewShipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Mounted in Surface Mount is this multiplexer. There is 8:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around -55°C~125°C TA. In total, there have been 16 terminations. A high-quality output is provided by the electrical component's 8 channels. A 4.5V voltage supply should turn on and run the electronic component. There is an electrical component included in the 16 series. A 1 circuit is present in this switch device. Look for analog switch ic variants by searching with M74HCT405. An switch multiplexer with 120Ohm internal resistance has a value of 120Ohm. To find out what the 16 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. A analog switch ic that has a cost-effective Dual supply type. The lowest voltage fed to the electronic component should be 4.5V. For this digital switch to work, 8μA current would suffice. For this switch, a dual supply voltage is feasible, but it must not exceed 6VWith dual power supplies, you should attach at least 1V. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. 5V operating voltages can be used with this electrical part. It is possible to operate 8 inputs. A 190MHz-bandwidth can be used for data transfer. M74HCT4051RM13TR Features8 Channels 8μA Supply Current Bandwidth: 190MHz M74HCT4051RM13TR ApplicationsThere are a lot of STMicroelectronics M74HCT4051RM13TR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote | |||
Texas Instruments | SN74LVC2G53YZPR OverviewPresented in 8-XFBGA, DSBGA, this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Cut Tape (CT). Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 2:1. Operational temperature extended around -40°C~85°C TA. The total number of terminations is 8. A electrical component with 2 channels is capable of high-quality output. An 2.3V voltage supply should allow the electrical part to be turned on and run. An injection of 8 pins is performed into the body of the electrical component. On the other hand, analog switches can be constructed using SPDT switching circuits. 1 circuits are used in this analogue multiplexer. Try searching for the analog switch ic with 74LVC2G53 if you are looking for variants. As far as internal resistance is concerned, it has 13Ohm. The functions of 8 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexers or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 1.65V. The analogue multiplexer could operate on 1μA current. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. The transfer of data can be performed over 300MHz bandwidths. There are 2 outputs on the analogue multiplexer. SN74LVC2G53YZPR Features2 Channels Switch Circuit: SPDT 1μA Supply Current -3db Bandwidth: 300MHz Bandwidth: 300MHz SN74LVC2G53YZPR ApplicationsThere are a lot of Texas Instruments SN74LVC2G53YZPR Analog Switches & Multiplexers ICs applications.
|
999
In-stock
|
Get Quote |
Please send RFQ , we will respond immediately.